Reliance electric GV3000 Instruction Manual Download Page 9

Page: 9 / 91

1.0 BECOMING FAMILIAR WITH THE MANUAL

This chapter provides help in finding information in the manual and describes the intended audience.

Also included are references to other related publications and instructions on receiving assistance

from Reliance Electric.

1.1 Finding Information

This instruction manual describes the GV3000 drive's Power Module and regulator hardware. It does

not cover the GV3000 software. For additional software information, refer to the GV3000 AC General

Purpose (V/Hz) and Vector Duty Drive Software StartUp and Reference Manual (D23339).
As an aid in finding information in this manual, each chapter is briefly described below:

Chapter 1

Becoming Familiar with the Manual

Provides information on how the manual is organized and where to find additional

information.

Chapter 2

About the Drive

Identifies drive components and shows their locations.

Chapter 3 Planning Before Installing

Presents information that must be considered when planning a drive installation.

Chapter 4

Mounting the Drive, Grounding, and Finding Wire Routing Locations

Describes how to mount the drive and properly ground it.

Chapter 5

Installing Input Power Wiring

Describes incoming AC and DC line components and how to properly connect

them.

Chapter 6

Installing AC Output Power Wiring

Describes output AC line components and how to properly connect them to the

motor.

Chapter 7

Wiring the Regulator Board Terminal Strip

Provides information on the I/O wiring that connects to the terminal strip on the

Regulator board.

Chapter 8

Completing the Installation

Provides instructions on how to perform a final check of the installation before

power is applied.

Chapter 9

Troubleshooting the Drive

Describes the equipment that is needed to troubleshoot the drive and how to

measure DC bus voltage. Replacement part lists are also provided.

Appendix A Technical Specifications

Lists drive specifications in table form.

Appendix B Drive Regulation Overview

Briefly describes volts/hertz and vector regulation.

Appendix C Compliance with EN 602041: 1992

Lists the sections of standard EN 602041: 1992 that the GV3000 drive complies

with.

StockCheck.com

Downloaded from StockCheck.com

Summary of Contents for GV3000

























































































Search results

Summary of Contents for GV3000

Reviews:

Related manuals for GV3000

Brands by name

Popular brands

Reliance electric GV3000, Instruction Manual

Search results

Summary of Contents for GV3000

Reviews:

Related manuals for GV3000

Brands by name

Popular brands