manualshive.com logo in svg

Reinhardt 1002-349-807, Manual

Share
Download
Reinhardt 1002-349-807 Manual Download Page 29

REINHARDT 

System- und Messelectronic GmbH

Fax: 08196/7005 und 1414 E-Mail: [email protected] http://www.reinhardt-testsystem.deBergstr. 33

86911 Diessen-Obermühlhausen Tel. 08196/7001 Fax: 08196/7005 und 1414

PM BD MWS6 E Page 28 of 34

Manual MWS 6

erstellt am 02.11.2000 von  DO

Option LCD-Display

The optional LCD-display for MWS6 / weather and climate sensors displays the
weather data and, if you like, also time, date and up to 4 comment lines in an
automatic run.

Display can be in parallel to recording with the PC or even without a PC.
If the display is connected to a PC, you connect the standard-MWS6-cable to the
display and connect it to the COM-Port of the PC (connection cable LCD - PC).
For use of the LCD-display, you need a power supply with a special wiring
(Standard supply with 12..15VDC voltage applied to pin 1 of the 9-pole
interface connector! ).
Never connect this cabling with its special wiringto the interface of your
PC, as the 12..15V at pin 1 of the interface connector might destroy the PC-
interface !!!

A terminal program helps to display all sensors, time, date and comment lines on the
LCD display.
Turn the switch on the rear of the LCD to "SET" in order to set this.
After you have switched the SET-mode, you ought to plug in and out the voltage
supply of the display (9-pole connector) for initialising.
Start a terminal program with data of interface and Baud-rate and make your
settings (e.g. terminal #2 9600).
When you are in the SET-mode and make your settings, both display and terminal
program will send the message "Keine Wetterdaten" about every 5sec, as in the  SET-
mode the connection to the weather station is interrupted.
When you set the display, please wait for the message "Keine Wetterdaten" after the
data are transmitted (#10 - Line feed) before you enter the following parameter;
otherwise the display possibly does not react on your new entry.
After you have made all your settings,you turn the switch to "STANDARD" and
initialise the display by plugging in and out the voltage supply. It takes about  20sec
(max.), until the display receives data from the weather station and displays them.

If a MWS6 weather station is connected to your display, time and date will adopted
from MWS6.

NOTE:
While you make your settings in the SET-mode, no data are transmitted from the
weather station to PC or display !!

Possible Displays

Option LCD-Display

NOTE

Changing the
Configuration

Summary of Contents for 1002-349-807




































Reviews:

No comments

Brands by name

Popular brands

Load more brands