Rehabed LEO Instructions For Use Manual Download Page 20 | Manualshive

Page: 20 / 56

Rehabed LEO Instructions For Use Manual Download Page 20

20

▪

Repeat the assembly process for the side rails on the
other side of the bed.

▪

Check that the side rails function properly and
smoothly. Check that the side rails easily lock into the
highest position to make sure that they are mounted in
a right way.

6.4.

F

ITTING THE

L

IGHT SIDE RAILS

The Leo bed is delivered with fitted steel Light side rails. The following instructions
may be helpful when you need to replace the side rails or their components.

▪

To fit the Light side rails, fix it to the bed according to the below picture, setting
it evenly on both mounting sleeves.

▪

Pay attention that the side rails release button is closer to the foot bed end.
Note: the side rails are the same for the right and left sides of the mattress
platform and they may be installed interchangeably.

6.5.

F

ITTING THE SPLIT SIDE RAILS

The Leo bed is delivered with fitted split side rails. The following instructions may be
helpful when you need to replace the side rails or their components.

«
...
18
19
20
21
22
...
»

Summary of Contents for LEO

























































Reviews:

No comments