Rehabed LEO Instructions For Use Manual Download Page 18

Page: 18 / 56

6.1.1.

OLDER ARRANGEMENTS ON POWER CABLE

Leo bed is equipped with 7 additional cable holders that allow the power cable
suspension under the mattress platform.

The figure below presents the arrangement.

▪

All cables must be suspended from the platform frame on
dedicated brackets, to avoid rubbing and cannot touch the
floor.

▪

Incorrect placement/deployment of the power cable may
cause the damage or cut of the cable

–

this situation may

expose live conductors (risk of electric shock).

▪

Consider the adequate placement of actuator and/or handset
cables in order to minimize the risk of accidental suffocation as
a result of the entanglement of the user and/or other people.

6.2.

SSEMBLING THE WOODEN BED ENDS

▪

Note: If this action is being undertaken the manufacturer recommend that
the castors are braked before assembly commences.

▪

Fit bed end sliding the spigot into the platform end and determine the position
of the set screws.

▪

Tighten all set and dome head screws, making sure the set screws are tightened
before tightening the dome head screws.

▪

Repeat for the other bed end.

▪

Cut off/remove the plastic retaining ties/Velcro straps from the head and foot
mattress platforms.

Summary of Contents for LEO

























































Search results

Summary of Contents for LEO

Reviews:

Rehabed LEO, Instructions For Use Manual, Page: 18 / 56

Search results

Summary of Contents for LEO

Reviews: