Regency P33CE-LP10 Owners & Installation Manual Download Page 5

Page: 5 / 56

P33CE-10 Direct Vent Gas Fireplace

safety decal

safety laBel

This is a copy of the label that accompanies

each P33CE Zero Clearance Direct Vent Gas

Fireplace. We have printed a copy of the contents

here for your review. The safety label is located

on the front inside base of the unit, visible when

the bottom louver is open.

NOTE:

Regency

units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

For the State of Massachusetts, installation

and repair must be done by a plumber or

gasfitter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, flexible con

nectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appli

ances individual manual shut-off must be a

t-handle type valve.

The State of Massachusetts requires the

installation of a carbon monoxide alarm in

accordance with NFPA 720 and a CO alarm

with battery back up in the same room where

the gas appliance is installed.

Summary of Contents for P33CE-LP10

























































Search results

Summary of Contents for P33CE-LP10

Reviews:

Related manuals for P33CE-LP10

Brands by name

Popular brands

Regency P33CE-LP10, Owners & Installation Manual

Search results

Summary of Contents for P33CE-LP10

Reviews:

Related manuals for P33CE-LP10

Brands by name

Popular brands