Regency Bellavista B36X Owners & Installation Manual Download Page 14

Page: 14 / 64

Regency Bellavista™ B36X Gas Fireplace

INSTALLATION

TOP FLUE COLLAR INSTALLATION

Note: This conversion must be done prior to the unit being placed in position.

The unit comes equipped as a rear vent unit. These instructions are to be used, only if the unit is going to be top vented.

Top Collar Assembly Kit

Intake Collar Assembly with Gasket

Intake Collar Plate with Gasket

Top/Rear Exhaust Assembly with Gasket

Heat De

ector

Baf

e Plate

1/4" x 1/2" Screws (4 spares)

Restrictor

Intake Collar Gasket (spare)

Exhaust Assembly Gasket (spare)

Exhaust Assembly

w/ gasket

Intake Collar Plate

w/gasket

Intake Collar Assembly

w/gasket

2) From inside the

rebox

, remove the top heat de

ector by removing

2 - 1/4" x 1/2" screws.

Heat De

ector

Diagram 2

1. Remove the door assembly by releasing the adjustable latches and lifting up off the door frame assembly.

Adjustable Tension

Latch location

Diagram 1

3) From inside the

rebox

, remove the baf

e plate by removing 4 - 1/4"

x 1/2 " screws. See Diagram 3

Baf

e Plate

Diagram 3

4) From the inside of the

rebox

, remove the exhaust assembly by

removing the 8 - 1/4" x 1/2" screws. See Diagram 4.

Diagram 4

UNIT ASSEMBLY PRIOR TO INSTALLATION

Summary of Contents for Bellavista B36X

































































Search results

Summary of Contents for Bellavista B36X

Reviews:

Related manuals for Bellavista B36X

Brands by name

Popular brands

Regency Bellavista B36X, Owners & Installation Manual

Search results

Summary of Contents for Bellavista B36X

Reviews:

Related manuals for Bellavista B36X

Brands by name

Popular brands