Regency Bellavista B36X Owners & Installation Manual Download Page 52

Page: 52 / 64

Regency Bellavista™ B36X Gas Fireplace

INSTALLATION

Finishing

Trim Top

Finishing

Trim Side

NOTE:

Install the Finishing Trim prior to installing the Flush Louvers.

Install the Finishing Trim sides as shown in the diagram; line up the holes in the
side trim with the holes in the fi rebox side.

Secure with 2 screws per side.

Loosen the 2 screws in the top inside edge of the fi rebox.

Slide the Finishing Trim Top over the Side Trim pieces and

fi t the bottom bracket slots over the screws. Tighten the 2
screws to secure in place.

Finishing Trim

Edge of Unit

OPTIONAL FINISHING TRIM INSTALLATION

FLUSH LOUVERS AND FLUSH PANEL INSTALLATION

To install the top and bottom louvers or

ush panels:

1) Locate the tabs on louvers/

ush panels.

2) Line up the tabs on louvers/

ush panels with the brackets on the

unit.

3) Hook the tabs up over the brackets to attach.

Tabs on Louver/Flush Panel

Bracket on unit for upper

Louver/Flush Panel

Bracket on unit for lower

Louver/Flush Panel

Installation of upper

Louver/Flush Panel

Installation of lower

Louver/Flush Panel

Summary of Contents for Bellavista B36X

































































Search results

Summary of Contents for Bellavista B36X

Reviews:

Related manuals for Bellavista B36X

Brands by name

Popular brands

Regency Bellavista B36X, Owners & Installation Manual

Search results

Summary of Contents for Bellavista B36X

Reviews:

Related manuals for Bellavista B36X

Brands by name

Popular brands