Regency B36XT Bellavista Owners & Installation Manual Download

Page: 14 / 68

Regency Bellavista™ B36XT Gas Fireplace

INSTALLATION

FINISHING

Non-combustible

Material

J-style Trim
or metal corner bead
may be used to finish these
edges

Non-combustible

Material

Non-combustible

Material

Diagram 2

Diagram 1

IMPORTANT FINISHING DETAIL NOTE:

Before placing unit into fi nal position - it is important to know the total
thickness / height of fi nished hearth (tile, carpet, etc.) The base of the
fi replace should be level or higher than the fi nished hearth height.

Diagram 3 Shown with optional fi nishing trim

Finishing material - thicker

than 1-1/4"

Important:

Finishing materials such as tile, river rock, etc,

must not

protrude

beyond the front facing fl anges the sides and top of the fi rebox
opening.

Full Screen Doors Only:

fi nishing with any material thicker than 1-1/4" - a 3/4" gap must

be maintained between the full screen doors and the fi nishing
material.

This gap is necessary to facilitate the installation and removal of the

full screen doors.

Note:

All non-combustible facing material should butt up cleanly

to the fl anges around the fi rebox opening.

Rough edges will be visible from the front view with the fl ush

louvers or fl ush panels - if not using the optional fi nishing trim.

To maintain a clean fi nished edge - it is recommended to install

the non-combustible facing material with the fi nished edge
against the fi replace / nailing strips.

Alternatively, you can use J Style Trim or Metal Corner Bead

to cover cut edges of the non-combustible facing material.

Diagram 5

Diagram 4

Full Screen

Door

3/4"

2 "

3 4

Note

: Full Screen Door Dimensions - page 6.

Summary of Contents for B36XT Bellavista





































































Search results

Summary of Contents for B36XT Bellavista

Reviews:

Related manuals for B36XT Bellavista

Brands by name

Popular brands

Regency B36XT Bellavista, Owners & Installation Manual

Search results

Summary of Contents for B36XT Bellavista

Reviews:

Related manuals for B36XT Bellavista

Brands by name

Popular brands