2
|
F5200 Regency Freestanding Woodstove
|
2
Thank you for purchasing a
REGENCY FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions
about your product that are not covered in this manual, please contact the
REGENCY DEALER
in your area.
Keep those
REGENCY FIRES
burning.
“This wood heater has a manufacturer set minimum low burn rate that must not be altered. It is against federal regulations to alter this
setting or otherwise operate this wood heater in a manner inconsistent with operating instructions in this manual." Failure to follow the
manual details can lead to smoke and CO emissions spilling into the home. It is recommended to have monitors in areas that are ex-
pected to generate CO such as heater fuelling areas..
“U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to comply with 2020 particulate emission standards using cord wood.” Model
Regency F5200 – 0.9g/hr."
SAFETY NOTE:
If this woodstove is not properly installed, a house fire may result. For your safety, follow the installation instructions,
contact local building, fire officials, or authority having jurisdiction about restrictions and installation inspection requirements in your area.
The following statements are required by the Environmental Protection Agency:
“This manual describes the installation and operation of the Regency F5200 catalytic equipped wood heater. This heater meets the 2020
U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters. Under specific test conditions this heater has been
shown to deliver heat at rates ranging from 16,600 BTU/hr to 47,100 BTU/hr.” Efficiency is determined using the B415 method resulting in
lower and higher heat values. This heater generates the best efficiency when operated using well-seasoned wood and installed in the main
living areas where the majority of the chimney is within the building envelope."
"It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if the
catalytic element is deactivated or removed."
"This wood heater contains a catalytic combustor, which needs periodic inspection and replacement for proper operation. It is against the
law to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if the catalytic element is deacti-
vated or removed."
CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, COAL,
PLASTIC,GARBAGE, SULPHUR OR OIL MAY DAMAGE THE CATALYST
"This heater is designed to burn natural wood only. Higher efficiencies and lower emissions generally result when burning air dried sea-
soned hardwoods, as compared to softwoods or to green or freshly cut hardwoods."
DO NOT BURN:
• Treated wood
• Lawn clippings or yard waste
• Manure or animal remains
• Coal
• Materials containing rubber including tires
• Saltwater driftwood or other previously salt water
saturated materials
• Garbage
• Materials containing plastic
• Unseasoned wood
• Cardboard
• Waste petroleum products , paints or paint thinners or asphalt products
• Paper products, cardboard, plywood or particle
board. The prohibition against burning these
materials does not prohibit the use of fire starters
made from paper, cardboard, saw dust, wax and
similar substances for the purpose of starting a
fire in a wood heater
• Solvents
• Materials containing asbestos
• Colored Paper
• Construction or demolition debris
• Trash
• Railroad ties
Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.
The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, etc.)
should be consulted before installation to determine the need to obtain a permit.
Note
: Due to the high efficiency of the F5200 unit, This unit
requires the use of double wall pipe
from the stove top to
either wall or roof exit. A minimum of 36" vertical rise is required prior to using any elbows.
This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to,
ULC629 in Canada or UL-103HT in the United States of America. or code approved masonry chimney with flue liner.
F5200 is tested and certified to ULC-S627-00 and UL1482-2011 (R2015).
SAVE THESE INSTRUCTIONS
