Regency Fireplace Products HRI3E-LP11 Owners & Installation Manual Download Page 8

Page: 8 / 64

8 |

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert

safety decal

This is a copy of the labels that accompany each LRI3E-11 Gas Insert.
We have printed a copy of the contents here for your review.

NOTE

: Regency units are constantly being improved. Check the label on

the unit and if there is a difference, the label on the unit is the correct one.

NATURAL GAS FIREPLACE INSERT:

MODEL LRI3E-NG11

Factory Equipped For Altitude 0-4500ft. (0-1370m)

Min. supply pressure

(1.37 kpa)

Low Setting Man. pressure

1.6"

(0.40 kpa)

Max. Manifold pressure

3.5"

(0.87 kpa)

Orifice size

#45

DMS

Minimum input

14,000

Btu/h (4.10 kW)

Maximum input

20,500

Btu/h (6.00 kW)

PROPANE GAS FIREPLACE INSERT:

MODEL LRI3E-LP11

Factory Equipped For Altitude 0-4500ft. (0-1370m)

Min. supply pressure

11"

WC (2.73 kpa)

Low Setting Man. pressure

6.4"

WC (1.59 kpa)

Max. Manifold pressure

10"

WC (2.49 kpa)

Orifice size

#55

DMS

Minimum input

15,500 Btu/h (4.54 kW)

Maximum input

19,000 Btu/h (5.57 kW)

Model/Modèle:

LRI3E-NG11

919-950a

Part #:

919-950a

Colour:

Black on grey except what is highlighted is printed red

Size:

(File at 100%) 6.503"W x 8.625" H

Material:

2 ml silver matt polyester (DPM SMS)

Oct 30/2018:

Created draft

Nov 05/2018:

New Serial #

Dec.14/18:

Added efficiencies

Jan. 21/19:

Remodeled the decal & added ‘’Canadian Energy Performance Verified’’

DO NOT REMOVE THIS LABEL /

NE PAS ENLEVER CETTE ÉTIQUETTE

Serial No. / No de série

488

Duplicate Serial number/Copie No de série

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.

FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE.

Model/Modèle:

LRI3E

- LP11

ENCASTRABLE AU GAZ PROPANE

MODÈLE LRI3E-LP11

ENCASTRABLE AU GAZ NATUREL

MODÈLE LRI3E-NG11

Pression d'alimentation minimale

Pression de sortie (manifold) - basse

Pression de sortie (manifold)

- max.

Taille de l'orifice

D bit calorifique minimal

D bit calorifique maximal

Min. Hearth Depth

Prof. min. âtre

D 12” (305mm)

Min. Hearth Width/

Largeur min. âtre

E 36” (914mm)

Max. Mantle Depth/

Prof. max. manteau G 12" (305mm)

Mantel Clearances / Dégagements manteau

Side wall /mur latéral A 6”

(152mm)

Ceiling/Plafond

B 60”

(1524mm)

Mantel/Manteau

C 38”

(965mm)

Min. Alcove Width/

Largeur min. alcôve

K 54"

(1372mm)

Max. Alcove Depth/

Prof. max. alcôve

L 36”

(914mm)

MADE IN CANADA /FABRIQUÉ AU CANADA

Minimum Clearances to Combustibles

from Insert/Dégagements min. combustibles

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and

Propane Installation Code, CSA B149.1.

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases unless a certified kit is used.

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured

(mobile) home where not prohibited by local codes. See owner's manual for details

WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original

parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.

Cet appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, conformément au National Fuel Gas

Code ANSI Z223.1, ou au CSA-B149.1 en vigueur.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison

préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de

renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.

Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si un kit certifié est utilisé.

AVERTISSEMENT : Ce foyer a été converti pour être utilisé avec un foyer au gaz encastrable et ne peut être utilisé pour brûler du bois ou d'autres

combustibles solides à moins que toutes les pièces d'origine aient été remises en place et que le foyer ait été homologué de nouveau par une autorité

compétente.

This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.

For use with glass doors certified with the appliance only. Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil.

For use only with barrier (Part # 716-010) Follow installation instructions. Pour utilisation uniquement avec l’écran(Pièce n°716-010)

Suivre les consignes d'installation.

Pression d'alimentation minimale

Pression de sortie (manifold) - basse

Pression de sortie (manifold)

- max.

Taille de l'orifice

D bit calorifique minimal

D bit calorifique maximal

Electrical supply / Alimentation électrique 115VAC, 2.5 A, 60Hz, Less than 10A

Fan Part # 911-207/Pièce ventilateur

C # 4001172

Listed:

VENTED GAS FIREPLACE HEATER/FOYER AU GAZ À ÉVACUATION

Certified to

/Certifi pour :

CSA 2.17-2017

ANSI Z21.88-2017

CSA 2.33-2017

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.

FPI Fireplace Products International, Ltd

Delta BC, CANADA

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 66.25%

Propane Gas / Gaz propane 66.70%

CANADIAN ENERGY

PERFORMANCE

VERIFIED

RENDEMENT

ÉNERGÉTIQUE

VÉRIFIÉ

EP5011169

For the State of Massachusetts, installation and repair must be done by a plumber or gas fitter licensed in the Commonwealth of
Massachusetts.

For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with

battery back up in the same room where the gas appliance is installed.

COPY OF SAFETY LABEL LRI3E-11

Summary of Contents for HRI3E-LP11

































































Search results

Summary of Contents for HRI3E-LP11

Reviews:

Related manuals for HRI3E-LP11

Brands by name

Popular brands

Regency Fireplace Products HRI3E-LP11, Owners & Installation Manual

Search results

Summary of Contents for HRI3E-LP11

Reviews:

Related manuals for HRI3E-LP11

Brands by name

Popular brands