Regency Fireplace Products HRI3E-LP11 Owners & Installation Manual Download Page 33 | Manualshive

Page: 33 / 64

background image

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert

| 33

installation

BRICK PANEL INSTALLATION

Important: This appliance cannot be operated without brick (LRI3E-11 only), enamel panels (HRI3E-11/LRI3E-11) or

painted panels (HRI3E-11 only) installed.

919-706

08.30.16

1

LRI3E

BRICK PANEL INSTALLATION

Brick panels are soft and fragile. Use caution when handling the panels,

being careful not to jar them or scratch the painted surfaces.

tooltip

tooltip

tooltip

1. Carefully unpack brick panels.

2. Install back brick panel - place against back wall of firebox, the side panels

(once installed) will secure the back panel in position.

Install back brick panel

Install left brick panel

Install right brick panel

Final install

3. Loosen bracket screw in firebox in location shown below, slide left brick

panel into position until it contacts the back panel. Slide the panel bracket
on from the front of the unit and tighten the bracket screw.

4. Loosen bracket screw in firebox in location shown below, slide right brick

panel into position until it contacts the back panel. Slide the panel bracket
on from the back of the unit and tighten the bracket screw.

«
...
31
32
33
34
35
...
»

Summary of Contents for HRI3E-LP11

































































Reviews:

No comments

Related manuals for HRI3E-LP11

Brand: Duraflame Pages: 8

Brand: Moda flame Pages: 10

Brand: Livoo Pages: 6

Wall Mantel with Base and Trim WD26CP

Brand: Desa Pages: 8

Brand: Twin-Star International Pages: 28

Ontario APCL**RN

Brand: Formosa Pages: 44

Brand: Kingsman Pages: 43

Brand: Dimplex Pages: 2

Comfort Glow CGFB32CB

Brand: Desa Pages: 36

Brand: Heat & Glo Pages: 81

Excalibur P90-LP

Brand: Excalibur Pages: 44

Brand: bemodern Pages: 10

Brand: Nibe Pages: 44

Brand: Hearth and Home Technologies Pages: 2

Brand: Paramount Fitness Pages: 6

MONTECITO ESTATE CAT

Brand: Astria Fireplaces Pages: 32

Brand: Megamaster Pages: 15

Brand: BFM Europe Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands