Regency Fireplace Products HRI3E-LP11 Owners & Installation Manual Download Page 48

Page: 48 / 64

48 |

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert

maintenance

VALVE REPLACEMENT

Before you begin:

* Shut off the gas supply to the unit.
Disconnect all electrical supply to the unit.

Always let the appliance cool to room temperature before servic-
ing.

Note:

To access the left control panel cover, the venting will need to be

disconnected (see vent/flue installation in this manual) for proper removal.

1. Remove the Faceplate, glass door and inner panels - see instructions in

this manual.

2. Remove the Left Control Panel Cover.

3. Disconnect gas line from valve.

tooltip

Remove

Loosen

LRI3E

HRI3E

burner cover

burner

LRI3E

- Remove the burner by removing 2 screws in locations shown below.

HRI3E

- Remove the burner by removing 5 screws in locations shown below

to remove burner cover and 2 screws to remove burner (shown below).

tooltip

4. Remove the burner.

Diagram 1

Diagram 2

Diagram 3

Diagram 4

5. Remove the burner support by removing 3 screws as shown below.

Diagram 5

Diagram 6

6. Remove the back deflector by removing 4 top screws and loosening 2

bottom screws.

7. Remove the valve access plate by removing 11 screws on the side panel

and 3 on the bottom as shown below.

Summary of Contents for HRI3E-LP11

































































Search results

Summary of Contents for HRI3E-LP11

Reviews:

Related manuals for HRI3E-LP11

Brands by name

Popular brands

Regency Fireplace Products HRI3E-LP11, Owners & Installation Manual

Search results

Summary of Contents for HRI3E-LP11

Reviews:

Related manuals for HRI3E-LP11

Brands by name

Popular brands