Regency Fireplace Products HRI3E-LP11 Owners & Installation Manual Download Page 39 | Manualshive

Page: 39 / 64

background image

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert

| 39

installation

BACKING PLATE INSTALLATION

919-711

09.08.16

1

3E

1. Remove Vignette (front) faceplate from unit and lay on a soft \

surface.

BACKING PLATE INSTALLATION

Final Install-shown with 4 sided backing plate

3. Attach the backing plate to the back faceplate from the front with 6

screws (4 along the top and 1 on each side).

4. Reinstall the back faceplate with backing plate—reverse Step 2.

5. Reinstall the Vignette faceplate and safety screen to complete.

tooltip

2. Remove the back faceplate by removing the 4 screws as shown.

Note:

the two top and two bottom screws can be loosened - slide the

back faceplate up on out to remove.

Remove Front Faceplate

Backing Plate Install

Remove Back Faceplate

tooltip

«
...
37
38
39
40
41
...
»

Summary of Contents for HRI3E-LP11

































































Reviews:

No comments

Related manuals for HRI3E-LP11

Brand: Panadero Pages: 30

Brand: J. A. Roby Pages: 3

Brand: Lamborghini Caloreclima Pages: 40

Brand: Travis Industries Pages: 7

Brand: Landmann Pages: 8

Brand: Hanover Pages: 13

Brand: baltur Pages: 92

Brand: Kenwood Pages: 24

Brand: Kenwood Pages: 42

Brand: Kenwood Pages: 47

Brand: Muskoka Pages: 12

Brand: Outdoor Lifestyles Pages: 33

Brand: Paramount Fitness Pages: 6

Brand: White Mountain Hearth Pages: 12

Brand: Heat & Glo Pages: 25

Brand: Heat & Glo Pages: 48

Brand: Megamaster Pages: 20

Brand: Baxi Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands