Regency Fireplace Products HRI3E-LP11 Owners & Installation Manual Download Page 1

Page: 1 / 64

Liberty® LRI3E / Regency Horizon® HRI3E

Gas Insert

Owners &

Installation Manual

www.regency-fire.com

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS
•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

MODELS: LRI3E-NG11 Natural Gas LRI3E-LP11 Propane
HRI3E-NG11 Natural Gas HRI3E-LP11 Propane

919-996e

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

10.14.21

Installer

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner:

Please keep these instructions for future reference.

Tested by:

Certified to/Certifié pour: CSA 2.17-2017
ANSI Z21.88-2017
CSA 2.33-2017

Summary of Contents for HRI3E-LP11

































































Search results

Summary of Contents for HRI3E-LP11

Reviews:

Related manuals for HRI3E-LP11

Brands by name

Popular brands

Regency Fireplace Products HRI3E-LP11, Owners & Installation Manual

Search results

Summary of Contents for HRI3E-LP11

Reviews:

Related manuals for HRI3E-LP11

Brands by name

Popular brands