REED ST-5500 Instruction Manual Download Page 9

reedinstruments

www

com

Power Tools & Small Appliances

This test would also apply to 
other similar equipment that 
has a line cord. For double 
insulated power tools, the 
megohmmeter lead shown 
(See graphic on page 8) 
connected to the housing 
would be connected to 
some metal part of the tool 
(ie: chuck, blade). Note:The 
switch of the device must 
be in the “ON” position and 
the main power should be 
disconnected.

Motors

AC-Disconnect the motor from the line by disconnecting the wires at  the 
motor terminals or by opening the main switch. If the main switch is  used 
and the motor also has a starter then the starter must be held, by some 
means, in the “ON” position. In the latter case, the measured resistance 
will include the resistance of the motor, wire and all other components be

-

tween the motor and the main switch. If a weakness is in dicated, the mo

-

tor and other components should be checked individually. If the motor is 
disconnected at the motor terminals, connect one megohmmeter lead to 
the grounded motor housing and the other lead to One of the motor leads. 
DC-Disconnect the motor from the line. To test the brush rigging,field 
coils and armature connect one megohmmeter lead to the grounded 
motor housing and the other lead to the brush on the commutator. If the 
resistance measurement indicates a weakness,raise the brushes off the 
commutator and separately test the armature, field coils and brush rigging 
by connecting one megohmmeter lead to each of them individually, leav

-

ing the other connected to the grounded motor housing. The above also 
applies to DC Gemerators. 

 

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Summary of Contents for ST-5500











Reviews: