REED ST-5500 Instruction Manual Download Page 8

reedinstruments

www

com

The above note also applies to testing at 1000V. In addition the following 
applies.

Note: 

Make sure that the circuit under does not include components 

Which will be damaged by the 1000V applied. Many normal components 
of an installation are likely to be damaged if tested at 1000V. Examples are 
power factor correction capacitors, low voltage mineral insulated cables, 
electronic light dimmers, electronic ballasts and starters for fluorescent 
lamps etc…

Lock Power on Feature 

For hands free operation a lock power on feature is incorporated in the 
press to test button. Set the LOCK button to lock test voltage, pressing it 
again will turn the tester off.

Low Resistance (Continuity) Measurements

1. Set the range switch to 200Ω •))) Position
2. Connect the red test lead to the V Ω terminal and back to the 

.

COM terminal.

3. Connect the tips of the test leads to both ends of the circuit under test. 

Read resistance in Ω on the LCD.

4. When the impedance on circuit is below approximately 40Ω.

.

It will indicate by a continuous beeper.

AC/DC Voltage Measurements

1. Set the range switch to ACV or DCV position
2. Connect red test lead to “V Ω” terminal and black test lead 

.

to terminal “COM”.

3. Connect test prods of test leads IN PARALLEL to the circuit 

.

being measured.

4. Read the voltage value on LCD.

 

REED Instruments

1-877-849-2127 | [email protected] | www.reedinstruments.com

Summary of Contents for ST-5500











Reviews: