background image

3

Introduction

Thank you for purchasing your REED R5020 AC Clamp Meter. Please 
read the following instructions carefully before using your instrument. By 
following the steps outlined in this manual your meter will provide years of 
reliable service.

Product Quality

This product has been manufactured in an ISO9001 facility and has been 
calibrated during the manufacturing process to meet stated product 
specifications. If a certificate of calibration is required please contact the 
nearest authorized REED distributor or authorized Service Center. Please 
note an additional fee for this service will apply.

Safety

• Never attempt to repair or modify your instrument. Dismantling your

product, other than for the purpose of replacing batteries, may cause
damage that will not be covered under the manufacturer's warranty.
Servicing should only be provided by an authorized service center.

• Do not exceed the maximum allowable input range of any function.
• Do not apply voltage to the meter when resistance function

is selected.

• Set the rotary switch to OFF when the meter is not in use.
• Set the rotary switch to the appropriate position before measuring.
• When measuring volts do not switch to current/resistance modes.
• Disconnect the test leads from the circuit under test before  changing

the position of the rotary switch.

• Do not exceed the maximum rated input limits.
• Improper use of this meter can cause damage, shock, injury or death.
• Always remove the test leads before replacing the battery.
• Inspect the condition of the test leads and the meter itself for any

damage before operating.

• Use great care when taking measurements if the voltages are greater

than 25VAC RMS or 35VDC as they are considered a shock hazard.

continued...

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for 800837001276

















Reviews: