background image

30

 HOW TO USE THE MAINTENANCE MODE

 1.  Select the settings main menu.

 

See step 1 on page 29.

 2.  Select the maintenance mode.

 

 In the settings main menu, touch the Maintenance 
button to enter the maintenance mode. 

 

 The maintenance mode main screen will show 
information about the console and the wireless 
network.

 3.  Update the console firmware.

 

 For the best results, regularly check for firmware 
updates.

 

 Touch the Firmware Update button to check for 
firmware updates using your wireless network. The 
update will begin automatically. 

 

 IMPORTANT: To avoid damaging the elliptical, 
do not turn off the power while the firmware is 
being updated.

 

 The screen will show the progress of the update. 
When the update is complete, the elliptical will turn  
off and then turn back on. If it does not, press the 
power switch into the off position. Wait for several 
seconds, and then press the power switch into the 
reset position. Note: It may take a few minutes for 
the console to be ready for use.

 

 Note: Occasionally, a firmware update may cause 
your console to function slightly differently. These 
updates are always designed to improve your exer-
cise experience.

 4.   Calibrate the incline of the ramp.

 

 Touch the Calibrate Incline button. Then, touch the 
Begin button to calibrate the incline of the ramp. 

The ramp will automatically rise to the maximum 
incline level, lower to the minimum incline level, 
and then return to the starting position. This will 
calibrate the incline. Press the Cancel button to 
return to the maintenance mode. When the incline 
is calibrated, touch the Finish button.

 

 IMPORTANT: Keep pets, feet, and other objects 
away from the elliptical while the incline is 
calibrating.

5.   Calibrate the screen.

 

 If the screen is not properly calibrated, it will be 
difficult for you to touch the correct buttons on the 
screen. To calibrate the screen, touch the Calibrate 
Screen button. A small target will appear on the 
screen. Note: Touch the Cancel button to return to 
the maintenance mode.

 

 Touch the center of the target. Then, touch the rest 
of the targets. After several seconds, the console 
will exit the calibration mode.

6.  View machine information.

 

 Touch the Machine Info button to view information 
about your elliptical. After you view the information, 
touch the back button on the screen.

7.  Find keycodes.

 

 This option is intended to be used by service 
technicians to identify whether a certain button is 
working correctly.

8.  Exit the maintenance mode.

 

 To exit the maintenance mode, press the back but-
ton on the console.

Summary of Contents for 1210 Elliptical









































Reviews: