background image

REDLAKE MASD, INC. 

LIMITED WARRANTY 

 
 
 

For a period of one (1) year from the date of shipment, the Redlake Product and any Redlake 
manufactured accessories (collectively the “Product”), shall perform substantially in accordance 
with the material provisions of the user manual for the Product (“Limited Warranty”).  If, because 
of a defect in workmanship or material, the Redlake Product fails to perform in accordance with 
the Limited Warranty, then, as the sole available remedy, Redlake shall repair or replace, at 
Redlake’s option, the Redlake Product or any part thereof.  The sole remedy of repair and 
replacement is contingent upon shipment of the Product, within the Limited Warranty period, to 
Redlake’s United States facility.  Redlake shall have no obligation under this Limited Warranty to 
provide local repair or replacement services for the Product, but will, at Redlake’s sole discretion, 
provide repair and replacement service under the terms of the Limited Warranty at its non-United 
States facilities upon prior written request of the Product Purchaser.   
 
 

NOTE:  THIS WARRANTY DOES NOT APPLY TO THE FOLLOWING CONDITIONS:

  

(1) damage caused by a failure to operate the Product in accordance with Redlake’s written 
instructions, including, but not limited to, environmental specifications listed in the Redlake user 
manual; (2) damage caused by accidental user damage, misuse or abuse of the Product; (3) 
damage caused by the unauthorized attempted repair of or tampering with the Product by non-
Redlake personnel; or (4) damage resulting from shipping of the Product. 
 
 
EXCEPT FOR THE LIMITED WARRANTY STATED IN THIS SECTION, REDLAKE DISCLAIMS 
ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, 
ANY WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR A 
PARTICULAR PURPOSE, REGARDING THE REDLAKE PRODUCT OR ANY PART THEREOF.  

 
 
IN NO EVENT SHALL REDLAKE BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR 
SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION LOSS OF BUSINESS OR 
PROFITS, EVEN IF REDLAKE RECEIVES NOTICE IN ADVANCE THAT THESE KINDS OF 
DAMAGES MIGHT RESULT, NOR SHALL REDLAKE’S AGGREGATE CUMULATIVE 
LIABILITY TO THE PRODUCT PURCHASER, PRODUCT RECIPIENT, OR PRODUCT 
CUSTOMER, PURSUANT TO ANY AND ALL CLAIMS AND LEGAL THEORIES (INCLUDING 
NEGLIGENCE AND BREACH OF CONTRACT), EXCEED THE ORIGINAL COST OF THE 
PRODUCT PAID TO REDLAKE BY THE ORIGINAL PURCHASER OF THE PRODUCT.

 

 
 
 
 
 
 
 
 
  
 
 

Redlake MASD, Inc. 11633 Sorrento Valley Road, San Diego, California 92121-1010 

(Redlake, 

Mega

Plus and 3M are trademarks.) 

91000116-001 Revision B 

1-2 

10/15/02 

Summary of Contents for MegaPlus ES 4.0/E









































Reviews: