Red Epic REDCAST Operation Manual Download Page 6

Page: 6 / 35

REDCAST MODulE OPERATION GuIDE

955-0072, REV-H | 6

INTRODUCTION

The REDCAST™ Module (formerly the RED 4K Broadcast Module) provides a 4K Ultra-High Definition (UHD)

video stream, enabling you to capture and view action in real-time. The REDCAST Module uses four (4) 1080p

3G-SDI output connections to broadcast 4K video at up to 59.94 frames per second (FPS).
Alternately, you can stream a full-frame 1080p video out of each 3G-SDI connector, providing four (4) additional

HD-SDI monitoring and recording paths.
For the first time, the unrivaled crisp and detailed images created by the EPIC DRAGON

and SCARLET

DRAGON

cameras can be broadcasted, creating a refined 4K viewing experience. The REDCAST Module adds

to the arsenal of features the EPIC DRAGON and SCARLET DRAGON offer. In addition to streaming a live 4K

UHD video feed from the REDCAST Module, the BRAIN

can simultaneously:

Record to SSD at 6K, 5K, or 4K.

Live stream at up to 1080p via the HD-SDI connector.

Live stream at up to 1080p via the HDMI connector.

Five (5) 1/4-20 mounting holes are built into the top of the module, allowing for various mechanical peripherals

to be attached.
You can apply 3D LUTs to the 3G-SDI outputs on the REDCAST Module.

NOTE:

The REDCAST Module features differ between v5.3 and v6.0 firmware. This operation guide describes

features available in both firmware versions. Unless noted otherwise, all screen shots are from v6.0.

REDCAST Module

REDCAST MODULE

INTRODUCTION

Summary of Contents for REDCAST




































Search results

Summary of Contents for REDCAST

Reviews:

Related manuals for REDCAST

Brands by name

Popular brands

Red Epic REDCAST, Operation Manual

Search results

Summary of Contents for REDCAST

Reviews:

Related manuals for REDCAST

Brands by name

Popular brands