Red Epic REDCAST Operation Manual Download Page 30

Page: 30 / 35

REDCAST MODulE OPERATION GuIDE

955-0072, REV-H | 30

SUPPORTED FREQUENCIES

FREQUENCY (HZ)

SMPTE STANDARD

23.98, 24.00, 25.00, 29.97, 30.00

HD-SDI
SMPTE ST 292 (1.485 Gbps)

50.00, 59.94

3G-SDI
SMPTE ST 424 (2.970 Gbps)
SMPTE ST 425 (2.970 Gbps)

1. Ensure you select a frequency supported by your monitor.

ATTACH REDCAST MODUlE

You can dock the REDCAST™ Module to the following devices:

Module Adaptor

+1 Adaptor Module

COMPATIBlE RED DEVICES

You can attach the following devices directly to the back of the REDCAST Module:

Pro Battery Module (Dual)

Pro Battery Module (Quad)

Quickplate Adaptor

Quickplate Module

REDMOTE

REDVOLT XL Module

COMPATIBlE TIMECODE AND GENlOCK DEVICES

The REDCAST Module is compatible with the same timecode generators and genlock devices as the DSMC

BRAIN

. For more information about what devices are compatible with the DSMC BRAIN, see the

DSMC

Operation Guide

, available at

www.red.com/downloads

REDCAST MODuLE

COMPATIBILITY

Summary of Contents for REDCAST




































Search results

Summary of Contents for REDCAST

Reviews:

Related manuals for REDCAST

Brands by name

Popular brands

Red Epic REDCAST, Operation Manual

Search results

Summary of Contents for REDCAST

Reviews:

Related manuals for REDCAST

Brands by name

Popular brands