background image

www.ReadyLIFT.com  

-

  Phone: (877) 759

-

9991

 

  

 

44

-

3060/44

-

3080IM

-

AC

 

 

 

 

 

 

 

 

 

 

 

(877) 759

-

9991

 

 

MON

-

FRI 7AM

-

4PM PST

 

OR

 

EMAIL:  support@readylift

-

ami.COM

 

 

WEBSITE:  ReadyLIFT.COM

 

 

**Please retain this document in your vehicle at all times.**

 

IF your ReadyLIFT

®

 product has a damaged or missing 

part, please contact customer service directly and

 

a new replacement part will be sent to you immediately.

 

For warranty issues, please return to the place of 

 

installation and contact ReadyLIFT.

 

 

Limited Lifetime Warranty

 

 

This unique product warranty proves our commitment to the quality and reliability of every product that 

ReadyLIFT manufactures. The ReadyLIFT product warranty only extends to the original purchaser of any 

ReadyLIFT product, if it breaks, we will give you a new part. Warranty does not apply to discontinued parts. 

 

 

Our Limited Lifetime Warranty excludes the following ReadyLIFT items; bushings, bump stops, ball joints, tie 

rod ends, heim joints and shock absorbers. These parts are subject to wear and are not considered defective 

when worn. They are warranted for 12 months from the date of purchase for defects in workmanship. 

 

 

This product warranty is voided if the vehicle is not aligned after kit installation and proper maintenance is 

routinely done. 

 

 

Product purchased directly from ReadyLIFT has a 90 day return policy on uninstalled products from the date 

of purchase (may be subject to restocking fee). Uninstalled product returns must be in the original Ready-

LIFT packaging. Please call 

(877) 759

-

9991 

to get an RGA# for any return. Customer is responsible for 

shipping costs back to ReadyLIFT.  

Returns without RGA# will be refused.

 Contact ReadyLIFT directly 

about any potentially defective parts prior to removal from vehicle. 

 

 

ReadyLIFT products are 

NOT 

intended for off

-

road abuse. Any damage or failure as a result from off

-

road 

abuse voids the warranty of the ReadyLIFT product. ReadyLIFT is 

NOT

 responsible for any subsequent dam-

ages to any related vehicle parts due to misuse, abuse, improper installation, or lack of maintenance. Fur-

thermore, ReadyLIFT reserves the right to change, modify or cancel this warranty without prior notice.

 

2020 GM HD 

6” 

and 

8” 

LIFT KIT

 

Summary of Contents for 44-3060



























Reviews: