manualshive.com logo in svg

Readiness Systems AED Sentinel, Installation Manual, Page: 15 / 16

Share
Download
Readiness Systems AED Sentinel Installation Manual Download Page 15

14

15

Troubleshooting

After you install and activate the AED Sentinel monitoring unit, you may receive a 

blinking red error light. This means AED Sentinel had a problem with either capturing an 

image of your status indicator, or with sending it to AED Sentinel Manager.

If you see the blinking red light during your installation process, try these steps to solve 

the problem.

1. Turn off the AED Sentinel monitoring unit using the power switch on the battery pack.

2. Wait a few seconds, then turn it on.

3. Try the installation process again using the steps in Activate the AED Sentinel 

Monitoring Unit, above.

If you still see a blinking red light after your second installation process, contact support 

at [email protected].

You’re Done!

You have successfully installed your AED Sentinel monitoring unit. It will monitor your 

AED and send you alerts and messages if the AED cabinet door is opened, the AED 

status indicator changes from Ready to Not Ready, or if you need to replace your AED 

batteries or pads.

As always, AED Sentinel is here to keep a watchful eye. If you need help, simply contact 

us at [email protected]. 

Summary of Contents for AED Sentinel

















Reviews:

No comments