
PROFESSIONAL AUDIO MIXER
6
14. Solo-Schalter
Schaltet das für die Kopfhörer ausge-
wählte Signal stumm, damit der Kanal einzeln abgehört
werden kann. Das Abhören erfolgt pre-fader oder post-
fader, je nach Stellung des Solomodus-Schalters.
15. Kanal-Fader
Zur laufenden Regelung des Kanal-Aus-
gangspegels, der, je nach Auswahl, an die linken und
rechten Main-Ausgänge, Sub 1/2 und Aux 2 weitergelei-
tet wird.
B. STEREO EINGANGS-KANÄLE
16. Mic-Eingang (CH 5/6, CH 7/8)
Hier werden die Mikro-
phone angeschlossen. Für diese Eingänge ist Phantom-
Power (+48 V) verfügbar.
HINWEIS:
Bitte verwenden Sie die Phantom-Power nicht
bei unsymmetrischen Mikrophonen.
17. Linker (Mono) Eingang
Akzeptiert sowohl symmetri-
sche als auch unsymmetrische 6,3 mm Klinkenstecker
mit einem Line-Signal. Der Eingang wird zum linken Aus-
gangsbus geleitet. Bei Nichtverwendung des rechten
Eingangs (18), wird auch der rechte Eingang mit dem
linken Eingangssignal versorgt, so dass der Kanal als
Mono-Kanal verwendet werden kann.
18. Rechter Eingang
Sämtliche Signale über diesen An-
schluss werden nur zum rechten Ausgangsbus geleitet.
19. 20 dB-Schalter
Dieser Schalter regelt die 20 dB-Ab-
schwächung für den Mic/Line-Eingang.
20. High Equalization
Ermöglicht die Anhebung oder Ab-
senkung der hohen Frequenzen (12 kHz und höher) um
+/-15 dB. Wirkt sich sowohl auf das linke als auch auf
das rechte Eingangssignal aus.
21. Mid Equalization
Ermöglicht die Anhebung oder Ab-
senkung der mittleren Frequenzen um die festgelegte
zentrale Frequenz 2,5 kHz um +/-12 dB. Wirkt sich so-
wohl auf das linke als auch auf das rechte Eingangssignal
aus.
22. Low Equalization
Ermöglicht die Anhebung oder Ab-
senkung der niederen Frequenzen (80 kHz und tiefer) um
+/-15 dB. Wirkt sich sowohl auf das linke als auch auf
das rechte Eingangssignal aus.
23. Aux 1/Mon Send
Regelt den Pegel des Kanal-Eingangs-
signals, der am Aux 1-Ausgang zur Verfügung gestellt
wird. Aux 1 Send findet post-EQ und pre-fader statt.
24. Aux 2/EFX Send
Regelt den Pegel des Kanal-Eingangs-
signals, der am Aux 2-Ausgang und am DSP-Eingang
(EFFECT) zur Verfügung gestellt wird. Aux 2 Send findet
post-EQ und post-fader statt.
25. Balance
Dreht man den Regler nach rechts, wird das
Eingangssignal des linken Kanals stufenweise abge-
schwächt. Dreht man den Regler nach links, wird das
Eingangssignal des rechten Kanals stufenweise abge-
schwächt.
14. Solo Switch
Mutes the signal selected for listening in
the headphones, allowing the channel to be heard alone,
pre- or post-fader, according to the position of the solo
mode switch.
15. Channel Fader
Provides continuously variable control
of the channel output level to the left and right main out-
puts, Sub 1/2 and Aux 2, as selected.
B. STEREO INPUT CHANNELS
16. Mic Input (CH 5/6, CH 7/8)
This is where you connect
your microphones. Phantom power (+48 V) is available
for these inputs.
NOTE:
If you are using unbalanced microphones, do not
use +48 V.
17. Left (Mono) Input
Accepts _” balanced jack input or
unbalanced sources at line level. Input is routed to the
left output bus. In the absence of a plug in the right in-
put (18), the left input signal is also provided to the right
input, so that the channel functions as a mono channel.
18. Right Input
Similar to the left input, any inputs to this
connector are only routed to the right output bus.
19. 20 dB Pad Switch
This switch controls the 20 dB input
attenuator for the Mic/Line input.
20. High Equalization
Pr/-15 dB of shelving equa-
lization control to boost or cut high frequency signals 12
kHz and above. Affects both left and right channel input
signals.
21. Mid Equalization
Provides +/-12 dB of cut/boost to
the midrange frequency channels. This control is cente-
red at 2.5 kHz. Affects both left and right channel input
signals.
22. Low Equalization
Pr/-15 dB of shelving equa-
lization control to boost or cut low frequency signals 80
Hz and below. Affects both left and right channel input
signals.
23. Aux 1/Mon Send
Adjusts the amount of mono-summed
channel input signal supplied to the Aux 1 output. Moni-
tor Send is post-EQ and pre-fader.
24. Aux 2/EFX Send
Adjusts the amount of mono-summed
channel input signal supplied to the Aux 2 output and
DSP input (EFFECT). Aux 2 Send is post-EQ and post-
fader.
25. Balance
When turned to the right, gradually attenuates
the left channel input signal. When turned to the left, gra-
dually attenuates the right channel input signal.
stage-sound
Summary of Contents for FMX-1202
Page 12: ...PROFESSIONAL AUDIO MIXER 12 stage sound APPLICATION EXAMPLE ANWENDUNGSBEISPIEL STEREO PA...
Page 13: ...stage sound PROFESSIONAL AUDIO MIXER 13 APPLICATION EXAMPLE ANWENDUNGSBEISPIEL VIDEO SETUP...
Page 14: ...PROFESSIONAL AUDIO MIXER 14 stage sound BLOCK DIAGRAM BLOCKSCHALTBILD FMX 1602...