background image

RBR#0008819revB

2

Table of contents

1

RBR

quartz³

 BPR

|

zero.....................................................................................................3

2

Specifications..................................................................................................................4

3

Hardware.........................................................................................................................7

3.1 Opening and closing the instrument .........................................................................7
3.2 RBR

quartz³

 BPR

|

zero interface.................................................................................8

3.3 Orientation and datum location ..............................................................................10
3.4 Underwater battery canisters ..................................................................................11

4

General maintenance ...................................................................................................12

4.1 Support kit.................................................................................................................12
4.2 Replacing the O-rings................................................................................................13
4.3 Replacing batteries ...................................................................................................15
4.4 Replacing desiccant capsules...................................................................................16
4.5 Cables and connectors .............................................................................................17
4.6 Cleaning the instrument...........................................................................................18
4.7 Calibrating the instrument .......................................................................................18

5

Oil purge container maintenance ................................................................................19

6

Repairs...........................................................................................................................21

7

Revision history.............................................................................................................22

Summary of Contents for quartz3 BPR zero























Reviews: