background image

Finned copper tube gas boilers & water heaters – Boiler Manual

2

  If the information in this manual is not followed  

exactly, a fire or explosion may result causing property, 

personal injury or loss of life.

Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other applianc
WHAT TO DO IF  YOU SMELL GAS:
•  Do not try to light any appliance.
•  Do  not  touch  any  electrical  switch.  Do  not  use  any 

phone in your building.

•   Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

•   If  you  cannot  reach  your  gas  supplier,  call  the  fire 

department.

Installation and service must be performed by a qualified 

installer, service agency or the gas supplier.

  Assurez-vous de bien suivre les instructions données 

dans cette notice pour réduire au minimum le risque 

d’incendie ou d’explosion ou pour éviter tout dommoge 

matériel, toute blessure ou la mort

Ne  pas  entreposer  ni  utiliser  d’essence  ou  ni  d’autres  

vapeurs ou liquides inflammables à proximité de cet  

appareil ou de tout autre appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
•  Ne pas tenter d’allumer d’appareil. 
•  Ne touchez à aucun interrupteur; ne pas vous servir 

des téléphones se trouvant dans le bâtiment.

•   Appelez immédiatement votre fournisseur de gas depuis 

un voisin. Suivez les intructions du fournisseur. 

•   Si vous ne purvez rejoindre le fournisseur, appelez le 

service des incendies.

L’installation  et  l’entretien  doivent  être  assurés  par  un 

installateur  ou  un  service  d’entretien  qualifié  ou  par  le 

fournisseur de gaz.

  Failure to properly vent this unit can cause excessive 

amounts of carbon monoxide resulting in severe 

personal injury or death!

DESIGNED AND TESTED ACCORDING TO A.S.M.E. 

BOILER  AND  PRESSURE  VESSEL  CODE,  SECTION 

IV FOR A MAXIMUM ALLOWABLE WORKING PRES-

SURE OF 160 PSI, 1103 kPa WATER.

BEFORE YOU START     .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .   2
RATINGS & CAPACITIES    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3
BOILER/WATER HEATER LOCATION  .  .  .  .  .  .  .  .  .  .  .  .  3
COMBUSTION AIR & VENTILATION  .  .  .  .  .  .  .  .  .  .  .  .  .  3

GENERAL VENTING GUIDELINES .  .  .  .  .  .  .  .  .  .  .  .  .  .  5
OUTDOOR VENTING .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10
COMMON VENT SYSTEMS    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    . 11
GENERAL PIPING REQUIREMENTS   .  .  .  .  .  .  .  .  .  .  .  . 12

HEATING SYSTEM PIPING   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
DOMESTIC WATER SUPPLY PIPING    .    .    .    .    .    .    .    .    .    .    .    . 17

GAS SUPPLY PIPING   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 20

ELECTRICAL WIRING    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    . 21

GENERAL OPERATION   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 21
OPERATING INSTRUCTIONS    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    . 22
SEQUENCE OF OPERATION   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 24
CHECKING & ADJUSTMENTS .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 25

HEATNET FIELD WIRING   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 26
CONTROL DESCRIPTION  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 28
DIAGNOSTIC  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 28
MAINTENANCE   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 31

TROUBLE-SHOOTING   .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    . 33

REPAIR PARTS  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 34
START-UP SHEET   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 40
MASS CODE   .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    .    . 42
WARRANTY   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 43

BEFORE YOU START

 

This manual covers the application, installation, operation and 

maintenance of a Futera III Series finned copper heating boiler/

water heater/pool heater (Canada only). To obtain the safe, 

dependable, efficient operation and long life for which this heating 

boiler/water heater was designed, these instructions must be read, 

understood and followed.

The Futera III Series finned copper heating boiler/water heaters 

have been design certified by CSA for use with natural and propane 

gas under the latest revision of ANSI-Z21.10.3/CSA 4.3, Gas Water 

Heaters, ANSI-Z21.13/CSA 4.9, Gas-Fired Low Pressure Steam 

and Hot Water Boilers ANSI-Z21.56/CSA 4.7 Gas-Fired Pool 

Heaters (Canada only) and CAN1-3.1, Industrial and Commercial 

Gas Fired Packaged Boilers. Each unit has been constructed and 

hydrostatically tested for a maximum working pressure of 

160 psi

1103 kPa

 in accordance with Section IV of the A.S.M.E. Boiler 

and Pressure Vessel Code.

Summary of Contents for Futera II Modulation













































Reviews: