background image

LOCK

LIGHT

35

ACCESSORIES 

Model 972RGD

Model 59LM

Model 974RGD

Model 970LM

Model 97LM

Model 1702LM

S

AFETY

S

IGNAL

3-Channel

Remote Control:
Includes visor clip.

S

AFETY

S

IGNAL

4-Channel

Remote Control:

Includes visor clip.

SECURITY

3-Channel Mini

Remote Control:

With key ring and Velco fastening
strip.

Extension Brackets:
(Optional) For safety sensor
installation onto the wall or floor.

Model 98LM

Motion Detecting Door
Control Panel:
Multi-function door control with motion
sensor that automatically turns opener
lights on for 5 minutes when it detects
a  person entering the garage. Sensor
can be easily deactivated when
desired.

Model 976LG

S

AFETY

S

IGNAL

2-Channel

Remote Control:
Includes visor clip.

Outside Keylock:

Opens the garage door
automatically from outside when
remote control is not handy.

Outside Quick Release:

Required for a garage with NO
access door.

10 foot Complete Rail:

To allow a 10 foot door to open
fully.

8 foot Complete Rail:

To allow an 8 foot door to open fully.

Model 973RGD

Model 1708LM

Model 1710LM

SECURITY

Keyless Entry:

Enables homeowner to operate
garage door opener from outside by
entering code on specially designed
keyboard. Also can add a temporary
pass code for visitors or service
persons. This temporary code can
be limited to a programmable
number of hours or entries.

Summary of Contents for Pilot 1265RGD





































Reviews: