Raven AutoBoom Installation Manual Download Page 79

Page: 79 / 92

Manual No. 016-0230-004 Rev. F

UltraGlide

11.

Cut the smaller male LEFT SOLENOID UP SENSE connector off the yellow wire on the AutoBoom harness
cable (P/N 115-0230-052).

12.

Plug the removed connector into the remaining LEFT SOLENOID UP SENSE connector on the AutoBoom
harness cable.

13.

Splice a ring terminal (not provided) onto the cut end of the cable.

14.

Connect the ring terminal to the signal side of the left up coil.

15.

Cut the smaller male LEFT SOLENOID DOWN SENSE connector off the black wire on the AutoBoom
harness cable.

16.

Plug the removed connector into the remaining LEFT SOLENOID DOWN SENSE connector on the
AutoBoom harness cable.

17.

Splice a ring terminal onto the cut end of the cable.

18.

Connect the ring terminal to the signal side of the left down coil.

19.

Cut the smaller male RIGHT SOLENOID UP SENSE connector off the wire on the AutoBoom harness
cable.

20.

Plug the removed connector into the remaining RIGHT SOLENOID UP SENSE connector on the AutoBoom
harness cable.

21.

Splice a ring terminal onto the cut end of the cable.

22.

Connect the ring terminal to the signal side of the right up coil.

23.

Cut the smaller male RIGHT SOLENOID DOWN SENSE connector off the wire on the AutoBoom harness
cable.

24.

Plug the removed connector into the remaining RIGHT SOLENOID DOWN SENSE connector on the
AutoBoom harness cable.

25.

Splice a ring terminal onto the cut end of the cable.

26.

Connect the ring terminal to the signal side of the right down coil.

Connect the Harness Cable to the Sensors

Locate the CENTER SENSOR connector on the AutoBoom harness cable.

Connect the CENTER SENSOR connector to the installed center rack sensor (P/N 063-0130-025).

Locate the LEFT SENSOR (OUTER) connector on the AutoBoom harness cable.

Connect the LEFT SENSOR (OUTER) connector to the installed left sensor cable (P/N 115-0171-527).

Locate the RIGHT SENSOR (OUTER) connector on the AutoBoom harness cable.

Connect the RIGHT SENSOR (OUTER) connector to the installed right sensor cable.

If optional inside boom sensors are installed, repeat the steps above to connect the sensors to the harness
cable.

Connect the Harness Cable to the Controller Cable

Route the AutoBoom harness cable (P/N 115-0230-052) toward the machine’s cab.

Remove the terminator from the machine’s harness in the cab.

Install the terminator on the 4-pin Deutsch connector of the AutoBoom harness cable.

Connect the CAN connector of the controller cable (P/N 115-0230-056) to the machine’s harness
connection from which the terminator was removed.

Connect the round 16-pin connector on the AutoBoom harness cable to the mating 16-pin connector on the
controller cable.

Connect the spade terminal on the controller cable to a switched power source on the machine.

Summary of Contents for AutoBoom




























































































Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands

Raven AutoBoom, Installation Manual

Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands