manualshive.com logo in svg

Rauch AXIS EMC ISOBUS, Original Instructions Manual, Page: 98 / 102

Share
Download
Rauch AXIS EMC ISOBUS Original Instructions Manual Download Page 98

No. Message in display

Meaning and possible cause

89 Disc speed too high

Alarm of the spreading disc sensor

•

The maximum RPM is reached.

•

The set RPM exceeds the maximum
admissible value.

90 AXMAT-Stop

The AXMAT function is automatically
deactivated and no longer regulates.

•

More than 2 sensors are reporting an
error.

•

Communication error

93 This disc type requires amodification on

theTELIMAT device.Please follow themounting
instructions!

Spreading disc S1 is installed and the machine
is equipped with TELIMAT. Spreading errors
possible during border spreading

•

This spreading disc type requires
conversion of the TELIMAT device.

6.2

Fault/alarm

An alarm message is displayed with a red frame and with a warning symbol.

Fig. 50: Alarm message (example)

6. Alarm messages and possible causes

98

5902180-h-gb-

AXIS EMC ISOBUS

Summary of Contents for AXIS EMC ISOBUS







































































































Reviews:

No comments