background image

16

1.

 After putting through the power, press "ON/OFF" button on remote controller to

    turn on the air conditioner.

2.

 Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN,  

    

HEAT

Only appliable to heat pump model

.

3.

 Press "▲" or "    " button to set your required temperature. (T

emperature can’t 

    be adjusted under auto mode).

4.

 Press "FAN" button to set your required fan speed: auto, low, medium and high

    speed.

5.

 Press "      " button to select fan blowing angle.

Operation guide

Replacement of batteries in remote controller

1. Press the back side of remote controller marked
    with "    ", as shown in the 

g, and then push out 

    the cover of battery box along the arrow direction.

2. Replace two 7# (AA

A 1.5V) dry batteries, and

    make sure the position of "+" polar and "-" polar
    are correct.
3. Reinstall the cover of battery box.

signal sender

battery

Cover of battery box

remove

reinstall

● During operation, point the remote co

ntrol signal sender at the receiving 

   window on indoor unit.

 The distance between signal sender and receiving window should be no 

   more than 8m, and there should be no obstacles between them.

● Signal may be interfered easily in the

 

room where there is fluorescent lamp 

   or wireless telephone; remote controller should be close to indoor unit during 
   operation.

● Replace new batteries of the same model when replacement is required.

● When you don’t use remote controller for a long time, please take out the 

   batteries.

● If the display on remote controller is fuzzy or there

’s no display, please    

   replace batteries.

NOTICE

Function introduction for combination buttons

WIFI 

f

unction(Not applicable)

Press "MODE" and "TURBO" button simultaneously to turn on or turn off WIFI 

function. When WIFI function is turned on, the "         " icon will be displayed on 

remote controller; Long press "MODE" and "TURBO" buttons simultaneously for 

10s, remote controller will send WIFI reset code and then the WIFI function will be 

turned on. WIFI function is defaulted ON after energization of 

● This function is only available for some models.

the remote controller.

Summary of Contents for RS-V9KE

















































Reviews: