background image

Explanation of Symbols

1.Damage the product due to improper use or misuse of the product;

2.Alter, change, maintain or use the product with other equipment without abiding

by the instruction manual of manufacturer;

After verification, defects are due to improper operation during transportation of

product;

4.

Operate, repair, maintain the unit without abiding by instruction manual or related

regulations;

5.

After verification, the problem or dispute is caused by the quality specification or

performance of parts and components that produced by other manufacturers;

6.

The damage is caused by natural calamities, bad using environment or force

majeure.

7.

After verification, the defect of product is directly caused by corrosive gas;

3.

Exception Clauses

Manufacturer will bear no responsibilities when personal injury or 
property loss is caused by the following reasons.

Indicates a hazardous situation that, if not avoided, will
result in death or serious injury.  

Indicates a hazardous situation that, if not avoided, could 
result in death or serious injury. 

Indicates a hazardous situation that, if not avoided, may
result in minor or moderate injury.  

Indicates important but not hazard-related information, 
used to indicate risk of property damage. 

Indicates a hazard that would be assigned a signal word 
WARNING or CAUTION.

DANGER

WARNING

CAUTION

NOTICE

If it needs to install, move or maintain the air conditioner, please contact dealer

 

or local service center to conduct it at first. Air conditioner must be installed,

 

moved or maintained by appointed  unit. Otherwise, it may cause serious

 

damage or personal injury or death.

When refrigerant leaks or requires discharge during installation, maintenance, 

or disassembly, it should be handled by certified professionals or otherwise in 

compliance with local laws and regulations.

Summary of Contents for RS-V9KE

















































Reviews: