15
Step 3: Remove the frame
Step 2: Remove the front panel and air filter
1. Take out the air conditioner from it’s packaging.
2. Hold the slot under the front panel, then uplift it outwards, and
remove the front panel( See Fig. 1)
3. Grip the tab on the end of the filter, lift it up, then pull it towards
yourself, pull the filter out(see Fig.2)
Fig.1
Fig.3
1. Remove two screws at the bottom of the frame
.
( See Fig. 3)
2. Disconnect the coupler plugs and make sure not to interfere with
the temperature sensor cable. Hold the left bottom side of the
frame, lift it up to unlatch the lower side, remove it toward you
( See Fig. 4)
Fig.2
Prior to installation
INSTALLATION INSTRUCTIONS
CAUTION
All side louvers of the cabinet must remain exposed
to the outside of the structure.
2. Install the unit where the sunlight does not shine directly on the unit. If the unit
receives direct unlight, build an awning to shade the cabinet.
3. There should be no obstacle, such as a fence or wall, within 50cm from the
back of the cabinet because it will prevent heat radiation of the condenser.
Restriction of outside air will greatly reduce the cooling efficiency of the air
conditioner.
Install the unit a little obliquely downward to outside not to leak the condensed
water into the room (about 3~4°).
Install the unit with its bottom portion 75~150cm above the floor level.
The power cord must be connected to an independent circuit. The yellow/
green wire must be grounded.
300mm or more
80mm or
more
Awning
Fence
Outdoor
side
Indoor
side
Wall
75~150cm
500mm or more
Level
Unit
About
3~4°
Option A
Air in
Air in
Air in
Air out
500mm Min.
Option B
45 brick cut away
to clear louvers
Front
O
45 brick cut away
to clear louvers
O
Brick
wall
Brick
wall
Air in
100mm
Air out
Air in
Louver
Top View
Fig.4
CAUTION: Before installing, remove all packaging from
inside the carton, along with any inserts placed into the
side louvers(if any).
Step 1: Select the best location
1. To avoid vibration and noise, make sure the unit is installed securely and firmly.
Remove inserts placed
into the side louvers
1
50mm Min.
1
50mm
Summary of Contents for RC-S70U
