background image

 

 

Please read this user manual carefully before using the device  
and keep it for future reference.

 

Following the manual's recommendations guarantees long-lasting and 
failure-free exploitation of the device

.

 

IT IS FORBIDDEN

 

 

1. Make repairs on your own and fail to comply with the rules contained in 
this manual regarding the connection and operation of the device;  
2. Store substances that may explode in the device, such as aerosols 
filled with combustible propellants; 
3. Place the device in the sun; 
4. Covering the inlet and outlet of air from the aggregate; 

5. Switching the device on to the mains without a properly 
functioning protective circuit system;

 

6. Use of extension cords and dividers to connect power. 
7. Use devices/objects that could cause an electric spark inside 
the device and in the aggregate chamber. 

WARNING! 

 

1. Incorrect connecting of the device to the mains may result in an 
electric shock.

 

2. In the event of sparks or breakdowns, immediately disconnect the 
device from the power supply by pulling the plug from the socket and 
calling an authorized service technician.

 

3. It is necessary to protect the wiring system and control system 
against water and mechanical damage. 
4. When servicing and replacing parts, the device must be 
disconnected from the power supply

 

 

CAUTION!

 

 

1. Before cleaning the condenser – 

switch the device off! 

2. When cleaning the condenser, do not use tools/objects that could 
cause an electric spark. 
3. Water condensation on glass panes and sheets at high relative 
humidity (over 60%) is a natural phenomenon. Long-term and frequent 
occurrence of dewing indicates inadequate ambient conditions and is 
not a basis for calling the service!

 

4. Take care when removing the glass panes. 
Breaking the glass panes can cause injury! 

 

 

i

The device is not intended for household use.

 

The device is not intended for outdoor use.

 

 

!

 

!

 

Summary of Contents for L-WB1

















Reviews:

Related manuals for L-WB1