Install the tap:
Install the tap:
Install the tap:
Install the tap:
This diagram shows the view of
the base of the tap (A1) with
the 98°C water handle to the
left of the body.
⚠
YOU MUST
CAREFULLY
ACKNOWLEDGE
THE INLETS AND
OUTLETS AS
SHOWN
1.
Screw the fixing stud (A8) into base of tap (A1) as shown on the diagram.
2.
Place the base plinth (A2) and base plinth seal (A3) onto the base of the tap (A1).
3.
Hand tighten the domestic hot in flexible hose (E1) as shown in the diagram.
4.
Hand tighten the domestic cold in flexible hose (F1) as shown in the diagram.
5.
Hand tighten the filtered cold in flexible hose (C1) as shown in the diagram.
Hand tighten the filtered cold in flexible hose (C1) as shown in the diagram.
Hand tighten the filtered cold in flexible hose (C1) as shown in the diagram.
Hand tighten the filtered cold in flexible hose (C1) as shown in the diagram.
⚠
⚠
⚠
⚠
TAKE CARE NOT
TAKE CARE NOT
TAKE CARE NOT
TAKE CARE NOT
TO INVERT (C1) & (B1).
TO INVERT (C1) & (B1).
TO INVERT (C1) & (B1).
TO INVERT (C1) & (B1).
DOING SO WILL RESULT
DOING SO WILL RESULT
DOING SO WILL RESULT
DOING SO WILL RESULT
IN NO FILTERED WATER
IN NO FILTERED WATER
IN NO FILTERED WATER
IN NO FILTERED WATER
6.
Hand tighten the filtered cold out flexible hose (B1) as shown in the diagram.
Hand tighten the filtered cold out flexible hose (B1) as shown in the diagram.
Hand tighten the filtered cold out flexible hose (B1) as shown in the diagram.
Hand tighten the filtered cold out flexible hose (B1) as shown in the diagram.
7.
Hand tighten the 110° rated steaming hot flexible hose (D1) into the centre inlet as shown on the diagram.
8.
Place the tap (A1-A3) centrally and straight to the tap hole, passing the fixing stud (A8), flexi hoses (B1, C1,
D1, E1 & F1) through the tap hole.
9.
Pass the lower gasket (A6) then the metal horseshoe (A7) over the fixing stud (A8). Note: only if the tap is
to be fitted to a stainless steel sink then the white triangular plate (A5) can be fitted where shown to
improve the stability of the tap.
10.
Using a 13mm box spanner or small adjustable spanner tighten fixing nut (A9) onto the fixing stud (A8).
11.
Screw pushfit (B3) into brass adaptor (B2) and pushfit (C3) into brass adaptor (C2)
⚠
We
We
We
We recommend using PTFE tape (do not use sealing compound) on the thread of
recommend using PTFE tape (do not use sealing compound) on the thread of
recommend using PTFE tape (do not use sealing compound) on the thread of
recommend using PTFE tape (do not use sealing compound) on the thread of the
the
the
the pushfit
pushfit
pushfit
pushfit fittings
fittings
fittings
fittings
to make a good seal without applying excessive force (which may damage the plastic pushfit if
to make a good seal without applying excessive force (which may damage the plastic pushfit if
to make a good seal without applying excessive force (which may damage the plastic pushfit if
to make a good seal without applying excessive force (which may damage the plastic pushfit if
overtightened).
overtightened).
overtightened).
overtightened).
12.
Screw pushfit (B3) and adaptor (B2) into the filtered cold out flexible hose (B1).
13.
Screw pushfit (C3) and adaptor (C2) into the filtered cold in flexible hose (C1).
14.
Connect the domestic hot water flexible hose (E1) to the hot water isolation valve (G1) using a section of
15mm pipe (G4) and compression nuts (G3) and olives (G2).