4
Rear Panel Hook-up
Power
The TTM 56S features an internal universal switching power
supply that operates on any AC mains 100 to 240 VAC, 50 or 60
Hz (most places in the world). All that is required when traveling
is the appropriate IEC line cord available in each country. The
universal supply is a major plus for the traveling DJ. The
POW-
ER
switch is just above the power connector. You know what to
do with this, but leave it off until everything is connected.
Inputs
PGM 1
and
PGM 2
each have two inputs, each assignable
PHONO or LINE. For a turntable input with RIAA compen-
sation, push the corresponding switch up to
PHONO.
For all
other sources such as CD or MP3 players, push the correspond-
ing switch down to
LINE
.
PHONO GROUNDS
provide independent ground connect
points for turntables. It is very important that each turntable
have a very good ground connection to one of these terminals.
The thumbscrews will come off if they are over-rotated, so be
careful not to spin them off and lose them.
AUX IN
may be used with a drum machine, groovebox,
sampler, or another mixer’s output for session mix. This Input is
mixed
after
the Crossfader and FlexFX loop.
MIC INPUT
is a balanced input specifically designed for a
dynamic mic (a condenser mic will not work).
1-CONDUCTOR SHIELDED CABLE
1-CONDUCTOR SHIELDED CABLE
T
=
SEND
R
=
RE
TURN
S
=
SHIELD
+
+
SEND
RETURN
+
+
SHIELD
SHIELD
SHIELD
Send/Return Cable Wiring (Insert Cable)
AUX
PHONO
GROUNDS
POWER
PGM 1
PGM 2
4
3
2
1
4
4
3
3
2
2
1
1
4 3 2 1
100-240V
50/60 Hz
20 WATTS
ACN 001 345 482
MADE IN U.S.A.
RANE CORP.
OUT
IN
OUT
IN
MIC
BALANCED
MASTER
OUTPUTS
R
L
R
L
R
L
R
L
R
L
R
L
LINE
PHONO
TTM 56S
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
EFFECTS
SEND
UNBALANCED
FlexFX
RETURN
TIP = SEND
RING = RTN
BALANCED
4
3
2
1
O
N
Effects Loops
MIC EFFECTS
insert jack is unbalanced. It is wired for ¼"
TRS, meaning Tip=Send, Ring=Return and the Shield or Sleeve.
This is an independent Effects Loop for the Mic. There is no en-
gage switch, so the Mic signal is always processed when you have
a plug inserted and an effects box connected. If you are connect-
ing to an effects processor with a Send/Return (sometimes called
Insert) jack, a single TRS cable will work. If your effects proces-
sor has separate Send and Receive jacks, you need a “Y” cable.
You can buy a Send/Return cable from your local music store, or
you can make one of your own as shown below.
FlexFX EFFECTS
jacks are unbalanced mono ¼" TS
(Tip and Sleeve). This stereo loop is used for output to (send)
and input from (return) an effects processor. The SEND jacks
provide the output
to
your effects processor. The RETURN jacks
provide input for the signal returning
from
your effects proces-
sor. If you have an effects device with a single ¼" TRS, tip=send,
ring=return jack, you need a “Y” cable, as shown below.
Outputs
AUX OUT
may be used for recording, booth monitoring, a
second playback zone, or connecting another mixer for session
mix.
AUX
OUT
is the same signal as the Master Mix with its
own Level control.
MASTER OUT
includes two sets of stereo outputs: The ¼"
TRS jacks provide balanced (Tip-Ring-Sleeve) output. Use this
balanced output whenever driving equipment with a balanced
input, or when running distances greater than 10 feet (3 meters).
Never
use a mono ¼" Tip/Sleeve (no ring) plug in this jack. Use
the RCA unbalanced outputs for shorter runs connecting to
unbalanced devices. See the RaneNote “Sound System Intercon-
nection” if you need to convert between balanced and unbal-
anced or run long distances.
