Rancilio EGRO 55 Series Technical Manual Download Page 95

Page: 95 / 114

- Section 6: Page 22 -

This form is to be completed by the service technician performing the Preventative Maintenance visit.

CHECKLIST FOR PM TYPE 2

NCLUDES

YPE

1 P

LUS

THE

OLLOWING

REW

ROUP

SSEMBLY

Replaced shower screens on upper and lower pistons

ATER

OILER

Brew Valve

Inspected and cleaned brew valve
Replaced coffee valve plunger - (PN 054055)
Replaced and lubricated O-rings to brew valve assembly

(PN:

043366)

OFFEE

OILER

XPANSION

ALVE

Replaced pressure relief valve - (PN 054055)

TEAM

OILER

Inspected and cleaned the level sensor

---> Recommended Decalciﬁ cations YES or NO

(please circle)

TEAM

AND

Cleaned steam wand and exchanged steam wand tip seal

(PN: 040501)

CHECKLIST FOR PM TYPE 1

REW

ROUP

SSEMBLY

(BGA)

Replaced BGA with new or rebuilt BGA

OR.....

If you changed O-rings on site please check the following

Lubricated and replaced upper piston O-rings
Lubricated and replaced lower piston O-ring
Cleaned shower screens on upper and lower

pistons

RINDERS

Inspected grinders
Cleaned hoppers

UTLETS

AND

TEAM

AND

Ran automatic coffee cleaning program
Cleaned tea outlet
Cleaned steam wand

ATER

FILTRATION

AND

SOFTENING

SYSTEM

Tested water hardness before installing

softening and ﬁ ltering system

--> Water Hardness is: GPG

Replaced water ﬁ ltration and softening

cartridges

Tested water hardness before installing

softening and ﬁ ltering system

--> Water Hardness is: GPG

Please complete and return form to verify that a preventative maintenance visit was performed.

RETURN TO:

Service Technician Name (Please Print)

Signature of Service Technician

Additional Notes/Comments:

CUSTOMER INFORMATION

SERVICE TECH INFORMATION

OMPANY

AME

ECHNICIAN

’

AME

OCATION

, C

ITY

, S

TATE

OMPANY

AME

ATE

HONE

UMBER

OTAL

YCLES

ERFORMED

E-

MAIL

LEANING

YCLES

ERFORMED

PM V

ISIT

YPE

1 or 2 (please circle)

YCLES

INCE

AST

(

SER V

)

IME

OMPLETE

hours mins

ACHINE

’

ERIAL

UMBER

6.6 PM GUIDE: CHECKLIST AND SIGN-OFF SHEET

Summary of Contents for EGRO 55 Series
















































































































Search results

Summary of Contents for EGRO 55 Series

Reviews:

Related manuals for EGRO 55 Series

Brands by name

Popular brands

Rancilio EGRO 55 Series, Technical Manual

Search results

Summary of Contents for EGRO 55 Series

Reviews:

Related manuals for EGRO 55 Series

Brands by name

Popular brands