background image

Section 6 – Warranty

15

Pressure gauges have not been exposed to frosting and freezing conditions and due care has been 

exercised when attaching them to any Waterco products; 

Electrical equipment has been adequately protected from salt air environments and from salt water; and 

Any pump used on a filter does not have a shut-off head that exceeds the pressure rating of the filter 

installed. 

All repairs and replacements shall be carried out by Waterco or its authorized service dealer, unless 

otherwise authorized in writing by Waterco. 

If an authorized service dealer is not available within 25 km of the purchaser’s area: 

• The purchaser must contact the place of purchase or Waterco for further instructions and; 

• The purchaser is responsible for any freight or infield labour costs. 

EXCLUSIONS 

This warranty does not cover, and Waterco will not be responsible for, any defect or damage caused 

or contributed to by: 

(a) installation or use of the product other than in accordance with Waterco’s written 

instructions, any statutory requirements and these terms and conditions; 

(b) use of the product for a purpose other than for which it was designed or sold; 

(c) abuse, misuse, corrosion, internal and external, or normal wear and tear; 

(d) any repairs or modifications whatsoever carried out by any person, other than a 

Waterco authorized service dealer; 

(e) exposure to water not caused by a defect in the product; and 

(f) transit of the product over which Waterco has no control. 

(g) inadequate ventilation 

(h) cement, pebbles, render or other pool surface finishes blocking the pump’s impeller 

(i) insect infestation 

Some three phase pumps are not supplied with thermal overload protection. It is the purchaser’s 

responsibility to have this provision installed by appropriately licensed electricians prior to the initial 

installation of the pump. All electrical work must comply with any appropriate statutory requirements. 

Warranty for installation of thermal overload protection is the sole responsibility of the licensed electrical 

contractor and not Waterco. 

Waterco excludes all liability it may have to the purchaser for indirect, special or consequential loss 

arising from or related to any defect in any Waterco product, or any act or omission of Waterco, including, 

but not limited to, loss of business, loss of profit, loss of revenue, lost opportunity, inconvenience, and 

damage to any property other than the Waterco product. 

Waterco excludes all other conditions, warranties, liabilities or representations which might, but for 

these terms and conditions, be implied by law or otherwise. These terms and conditions do not exclude 

or modify any implied condition or warranty, or any liability imposed on Waterco by any law (including 

the Trade Practices Act), if to do so would contravene that law or make any part of these terms and 

conditions void. 

To the extent permitted by law, Waterco excludes all conditions and warranties implied into these terms 

and conditions and limits its liability for breach of any such condition or warranty that it cannot exclude 

to the greater of (at Waterco’s option); 

(a) for goods: 

• Repairing or replacing those goods; or 

• Paying the cost of having those goods repaired or replaced; and 

(b) for services: 

• Resupplying the services; or 

• Paying the cost of having those services resupplied. 

Summary of Contents for Waterco Chemflo 25880
















Reviews: