Rail King SD70ACe Operation Manual Download Page 16 | Manualshive

Page: 16 / 56

background image

™

Proto-Coupler Operation

This locomotive is equipped with one or more coil-wound Proto-Couplers for remote

®

uncoupling action. Because Proto-Couplers are controlled through the Proto-Sound
3.0 microprocessor, they do not require an uncoupling track section or modification to
your layout to function. You can fire a coupler from neutral or while in motion. Use the
code shown below (and in the chart on p. 30) to fire the coupler(s).

Rear Coupler:

To fire the rear coupler, quickly tap the Bell button once followed by three quick taps of  the
Horn button, allowing approximately ½ second to lapse between each quick button press.
The sound of  the liftbar and air line depletion will play, and the knuckle will be released.

Front Coupler:

To fire the front coupler (if  your engine has one), quickly tap the Bell button once
followed by four quick taps of  the Horn button, allowing approximately ½ second to
lapse between each quick button press. The sound of  the liftbar and air line depletion
will play, and the knuckle will be released.

Horn

Horn

Fire

Rear

Coupler

=

Horn

Bell

Horn

Horn

Fire

Front

Coupler

=

Horn

Horn

Bell

Tips on Using PFA

• You can terminate PFA at any time by turning off power to the track for 15 seconds.

• You do not have to be in Forward to use PFA. At the conclusion of the full sequence,
the train will pull away from the station in whatever direction you were going when you
activated the feature.

• You can use PFA even if you are double-heading with another engine. If the second

®

engine is not equipped with Proto-Sound 3.0, you must remember not to leave the
throttle at a high voltage level once you have stopped the engine to run the PFA.
Otherwise, the engine without PFA will begin vibrating on the track as its motors strain
to move the train, since they cannot be automatically disabled during the PFA cycle (or if

®

an original Proto-Sound engine, PFA are triggered differently and that engine's motor-

®

disable feature will not be active when you run PFA in Proto-Sound 3.0).

• PFA can be triggered from Neutral. It will operate the same as if  triggered while in
motion except that, at the conclusion of  the PFA, the engine will depart in the next
direction of  travel, as opposed to the direction it was traveling before entering Neutral.

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

16

«
...
14
15
16
17
18
...
»

Summary of Contents for SD70ACe

























































Reviews:

No comments

Related manuals for SD70ACe

Brand: REVELL Pages: 11

Brand: Horizon Hobby Pages: 2

Brand: Fisher-Price Pages: 2

Lokpuffer Puff-H0

Brand: Fichtelbahn Pages: 2

Call of Duty CNG98

Brand: Mega Bloks Pages: 32

AMAZING ANIMALS M3198

Brand: Fisher-Price Pages: 4

NORTH AMERICAN T-28 TROJAN

Brand: SG Models Pages: 34

Brand: Fisher-Price Pages: 6

Batman Power Wing Laptop

Brand: Oregon Scientific Pages: 24

Brand: Faller Pages: 12

Brand: Rail King Pages: 23

Brand: Trix Pages: 24

Brand: Stevens AeroModel Pages: 4

Brand: Pilot Communications Pages: 37

P-51D Mustang 40

Brand: Kyosho Pages: 18

Brand: THUNDER TIGER Pages: 12

Brand: Avios Pages: 34

mini dual deploy DX3

Brand: Madcow Rocketry Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands