Rail King SD70ACe Operation Manual Download Page 15 | Manualshive

Page: 15 / 56

Rail King SD70ACe Operation Manual Download Page 15

Feature to Be Activated

Button Code:

Toggle the Marker Lights (if equipped)
PFA (Passenger/Freight Announcements)
Fire the Rear Coupler
Fire the Front Coupler
Speed Control On/Off
Lock into a Direction
Ditch Lights (On/Off)*
Reset to Factory Defaults

1 Bell, 1 Whistle
1 Bell, 2 Horn/Whistles
1 Bell, 3 Horn/Whistles
1 Bell, 4 Horn/Whistles
1 Horn/Whistle, 2 Bells (from Neutral only)
1 Horn/Whistle, 3 Bells
1 Horn/Whistle, 4 Bells
1 Horn/Whistle, 5 Bells (from Neutral only)

*Only applicable to engines equipped with ditch lights

Passenger/Freight Announcements (PFA)

Your engine is equipped with a sound package of either passenger station announcements
or freight yard sounds that you can play when you pull into a station or a yard. Each
sequence described below will play as long as it is left on, randomly generating sounds, but
be sure to allow approximately 30 seconds between the button pushes described below to
allow the PFA sufficient time to run through each sequence.

• To cue the sound system to play the PFA, quickly but firmly tap the Bell button once
followed by 2 quick taps of  the Horn button while the engine is moving. Tap the
buttons quickly but allow approximately ½ second between each press.
• Press the Direction button once to stop the engine. This will trigger the first
sequence of  PFA. The reverse unit is temporarily disabled so that the train will not
move as you use the Direction button to trigger the sounds. Proto-Sound 3.0 has
disabled operator control over the Horn and Bell buttons until the full PFA sequence is
complete.
• After waiting about 30 seconds for that sequence to run, press the Direction button
again to trigger the second sequence of  PFA.
• After about 30 seconds, press the Direction button again to trigger the third PFA
sequence.
• Again, after allowing about 30 seconds for that sequence to run, press the Direction
button one more time to trigger the fourth and final PFA sequence. The PFA will
continue and within a few seconds the bell will begin ringing, then the engine will begin
moving at the current throttle setting, in the same direction it was traveling when you
began the sequence. Once the bell turns off, the operator regains control of  the
transformer's bell and Horn buttons and can ring the bell or blow the Horn as usual.

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

Marker Lights (On/Off)

By default your Marker Lights are set to ON. To toggle them On/Off, perform the
following sequence on your AC transformer below:

Marker Lights

On/Off

=

Horn

Bell

15

«
...
13
14
15
16
17
...
»

Summary of Contents for SD70ACe

























































Reviews:

No comments