Rail King SD70ACe Operation Manual Download | Manualshive

Page: 23 / 56

background image

Master Volume

The operation for F6 (Master Volume) in DCC has changed to the following functionality:
When you activate F6, the Master Volume will begin increasing. If  you are at 0 (no volume),
the first time you turn on F6 it will take approximately 3 seconds to get to 100% volume.
When you get to your desired volume level then turn F6 off.
The next time you toggle F6 on it will drive the master Volume to 0. If  you are 100% it will
take approximately 3 seconds to get to 0. When you arrive your desired level turn F6 off.
It works like a volume slider – The first time you enable F6 it goes up and stops at 100%,
toggle F6 off  then back on and it will go down to 0 and stop.

Couplers

Your MTH PS3.0-equipped engine comes with remotely controlled Proto-Couplers. They
can be fired using your DCC handheld.
F7 – Front Coupler. Pressing F7 twice (toggling on then off) will fire your Front Coupler
F8 – Rear Coupler. Pressing F8 twice (toggling on then off) will fire your Rear Coupler

Forward/Reverse Signal

Just like a real engine, you can announce the direction of intended movement using your
DCC handheld and F9 and F10.
F9 – Forward Signal. Pressing F9 twice (toggling on then off) will sound the Forward Signal.
This is two whistle/horn blasts
F10 – Reverse Signal. Pressing F10 twice (toggling on then off) will sound the Reverse
Signal. This is three whistle/horn blasts

Grade Crossing Signal

Again, just like a real engine, you can trigger the Grade Crossing Signal on your engine. This
is two long, one short, one long whistle/horn blast.
F11 – Grade Crossing Signal. Pressing F11 twice (toggling on then off) will sound your
Crossing Signal.

Engine Sounds

Engine Sounds – F25. You can turn the Engine Sounds On/Off by pressing the F25
button. Pressing it once (enabling F25) will cause the Engine Sounds to shut off. The
Whistle/Horn and Bell sounds will still be active, however. To turn the engine sounds
back on press the F25 button again (disable F25).

Smoke (if Equipped)

F12 – Smoke On/Off. Enabling F12 will turn the smoke unit on. Disabling F12 will turn
your smoke unit off.
F13 – Smoke Volume. There are three smoke volume levels in your MTH PS3.0-equipped
engine – Low/Med/High. The default for this is set to High. You can adjust the smoke
output (amount of smoke the generator puts out) by pressing the F13 button twice. This
sets the level to the next step. For example, if you are currently at the High smoke output
level, pressing F13 twice (toggling it on then off) will set the smoke volume to Low. Pressing
F13 twice again will set it to Medium and so on.

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

23

«
...
21
22
23
24
25
...
»

Summary of Contents for SD70ACe

























































Reviews:

No comments

Related manuals for SD70ACe

Brand: Minicraft Models Pages: 4

Brand: Connoisseur Models Pages: 14

Cathy II P-51 Mustang

Brand: AIR core Pages: 2

Micro Sport Cub S2

Brand: Rage Pages: 12

Fordhampton Garden center

Brand: GAUGEMASTER Pages: 4

Z-Scale Ford F6 Truck Kit

Brand: EA Electronics Pages: 2

Spring Rocking Horse

Brand: QABA Pages: 3

Brand: Power Wheels Pages: 32

Brand: marklin Pages: 20

Brand: Spin Master Pages: 3

Brand: Solly Systems Pages: 56

Brand: Wilhelm Schroder Pages: 4

Brand: marklin Pages: 40

Hyper Hawk – HCAA0204

Brand: Flyzone Pages: 2

Brand: Opitec Pages: 7

Brand: PBS KIDS Pages: 49

E-FLITE UMX ASK-21

Brand: BNF Pages: 21

LICHTENSTEIN CASTLE

Brand: Faller Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands