Rail King SD70ACe Operation Manual Download Page 7 | Manualshive

Page: 7 / 56

background image

Connecting the Transformer & Installing DCS Remote
Commander Set

Your set comes with M.T.H.'s latest DCS System, the DCS Remote Commander. The
DCS Remote Commander includes a handheld Remote which communicates with a
Receiver powered by a UL approved Transformer to provide an easy-to-use, safe power
source for your new train set. To install the DCS Remote Commander and Transformer
please use the following instructions:

1. Ensure the Z-500 transformer is unplugged.

2. Install two AA batteries (not included) into the Remote. You will need a small screw
driver.

3. Plug the Z-500 transformer barrel jack into the port labeled “Power” on the
Receiver. Using the RealTrax Wire Harness plug the color-coded wires from the
Receiver to the Lighted Lock-on.

4. Make sure that the engine and cars are properly assembled and coupled on the track
and then plug the Z-500 transformer into any 110 volt AC wall outlet. You will know
that you have power to the receiver and the track if you see the green LED atop the
Receiver and the green light atop the Lighted Lock-on will come on. Subsequent
pushes of any buttons on the remote will cause the green LED atop the Receiver to
blink, indicating it is receiving the signal.

See Illustrations Below

Red Harness
Wire/Plug

Black Harness
Wire/Plug

Lighted Lock-on

Receiver

Z-500 Transformer

Remote

Red Harness
Wire/Plug

Black Harness
Wire/Plug

™

RailKing® SD70ACe Diesel Ready-To-Run Set w/Proto-Sound® 3.0

7

«
...
5
6
7
8
9
...
»

Summary of Contents for SD70ACe

























































Reviews:

No comments

Related manuals for SD70ACe

Brand: J-Power Pages: 32

Schlossberg Inn

Brand: Faller Pages: 12

Brand: M.T.H. Pages: 24

Brand: Hyperion Pages: 41

Brand: marklin Pages: 32

Brand: Top R/C Hobby Pages: 13

Brand: AMATI Pages: 56

Brand: VTech Baby Pages: 10

PENNSYLVANIA K4 STREAMLINER

Brand: Lionel Pages: 2

Brand: bruder Pages: 2

Brand: Jamara Pages: 24

Sit-to-Stand Learning Walker

Brand: VTech Pages: 16

Taylorcraft 130

Brand: Ares Pages: 32

Brand: K'Nex Pages: 16

Brand: Fisher-Price Pages: 6

Brand: Peg-Perego Pages: 48

Brand: Radica Games Pages: 2

Brand: marklin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands