SG Models NORTH AMERICAN T-28 TROJAN Assembly Manual Download | Manualshive

Page: 1 / 34

background image

Instruction Manual.

1

A S S E M B L Y M A N U A L

Specifications:

Wingspan---------------63.0 in (160 cm).
Wing area---------------349.5 sq.in ( 41.9 sq.dm).
Weight-------------------8.8-9.9 lbs ( 4.0 kg).
Length-------------------50.7 in ( 128.7 cm).
Engine-------------------10-15cc
Motor size---------------1200-1500 Watts
Radio--------------------6 channels with 7 servos.
Electric Power Conversion Included.

“ Graphics and specifications may change without notice ”.

Code: SEA258

1
2
3
...
»

Summary of Contents for NORTH AMERICAN T-28 TROJAN



































Reviews:

No comments

Related manuals for NORTH AMERICAN T-28 TROJAN

Brand: B Pages: 2

Super Decathlon 40

Brand: GREAT PLANES Pages: 44

Brand: ProBoat Pages: 20

Explore Dinosaurs National Geographics KIDS

Brand: InspirationWorks Pages: 2

Brand: GAME OF BRICKS Pages: 31

Brand: Lionel Pages: 2

PENNSYLVANIA K4 STREAMLINER

Brand: Lionel Pages: 2

ZAG HEROEZ Miraculous Pixelo

Brand: Lansay Pages: 2

Ju 88A interior S.A.

Brand: Eduard Pages: 2

Super PNP F-100D Super Sabre

Brand: Flex innovations Pages: 32

Brand: Fisher-Price Pages: 6

Brand: Smoby Pages: 4

Brand: Fisher-Price Pages: 5

Brand: Plum Pages: 13

Discovery Wall 8621

Brand: Step2 Pages: 4

Brand: Fisher-Price Pages: 4

Brand: E sky Pages: 29

Brand: THINK GIZMOS Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands