Raider Pro RDP-ID28, User Manual

Page: 11 / 102

11
7. Information on noise and vibration This kind of power is widely used for boring holes in wood, dendroid materials,
metal, ceramics and synthetic materials in the working mode without impackt, as well as concrete, brick and similar materials
in the operating mode of attack. Power electronic controls for right and left direction of rotation can be used to develop
cornering or screw joints. The areas of use are carrying out repair and construction, carpentry and other work-related self-
amateur activity. Not permitted the use of power tools for activities other than its intended purpose. emitted.
The values are measured according to EN ISO 3744:2010. A level of noise generated is generally: the sound pressure
level LpA 75 dB (A); sound power LwA 86 dB (A). Uncertainty K = 3 dB. Work with a earmuffs! The resultant value of vibration
(the vector sum of the three directions) is determined according to EN 60745: Drilling in metal: the value of the emitted
vibrations a
h
= 2.30 m/s
2
, uncertainty K = 1,5 m/s
2
, hammer drilling in concrete: value the emitted vibrations a
h
= 8.12 m/s
2
,
uncertainty K = 1.5 m/s
2
, cornering / development: the value of the emitted vibrations a
h
<2,5 m/s
2
, uncertainty K = 1,5 m/
s
2
. That in this operating manual for the vibration value is measured by the method specified in EN 60745 and can be used
to compare different power. The level of vibration varies depending on the specific activity carried out and in some cases
may exceed that amount in that direction. If power is used for a long time in this mode, the load caused by vibration, could
be underestimated. Directions: For an exact estimate of the burden of vibrations in a working cycle should be recorded and
the intervals in which the power is off or idling. This can significantly reduce the reporting burden of vibrations throughout
the business cycle.
8. Preparing for the job. Installation of accessories and auxiliary tools.
8.1.1. Auxiliary handle.
Use only the impact drill fitted with an auxiliary handle (8). You can insert auxiliary handle (8) in practically any position, to
ensure your comfortable and safe position for the job. Turn the handle itself (8) axis and counterclockwise, thus reducing the
firmness of the loop around the head of the drill and you can rotate the auxiliary handle in the desired position. Then tighten
the grip again (8), such as turning it clockwise.
8.2. Setting the depth of drilling. With deep baffle (5) can be pre-set depth of drilling. Pull the baffle so deep that the
distance along the axis between the tip of the drill and deep baffle is equal to the desired depth of the hole.
8.3. Placing the drill in the chuck. Turn off the power of power. Put the key in one of the open side of the chuck. Dissolving
the jaws to the desired size and place in the drill chuck. With key-locking in three successive drill a hole in the chuck. We
must always remember that the key should be removed from the drill after the completion of operations related to installation
and dismantling of the drill. When mounting a new drill should be checked by the inclusion of a short drill, drill that rotates in
an axis without “flicker”. This will help us make sure that it is not distorted.
8.4. Inclusion and exclusion. Beware of the voltage of supply network! Supply voltage of the network must conform to the
details shown on the plate of power. Appliances marked with 230 V, can be supplied with a voltage of 220 V.
8.5. To turn the drill press and hold the trigger switch (1). For locking of the starting switch pressed (1) press (3). Exclusion
relax power trigger switch (1), respectively, if anchored to the button (3), first press the short term and then release the trigger
switch (1).
8.6. Adjust the speed of rotation. Drill allows to work with different speed of spindle. Alignment is done using the position
(2). In the range of each setting a speed can be adjusted smoothly by increasing speed and reducing pressure on the trigger
button (1). Turn right speed regulator (2) leads to increase their rotation and left to decrease.
8.7. Correct choice of the rate of speed shall be held where drill is included without load. So speed-minded when working
with a load may be lower.
8.8. Hammer drilling.
Place the switch (6) the symbol “hammer drilling.” Switch (6) falls in the correct position with a distinct twinge.
8.9. Tools to develop or cornering.
Turntable working instrument can be bent. After continuous operation with low-speed power to cool as to leave it idling
for approximately 3 minutes with a maximum speed of rotation. When working with terminals must always use a universal
extension. Use only the cores that are suitable for heads of screws. Turning to always place the switch “drilling / hammer
drilling» (6) in position «Drilling».
8.10. Select the direction of rotation. With the switch (4) you can change the direction of rotation of power. Rotate right:
For drilling and turning the screw press to switch the direction of rotation (4) at point blank range left. Rotate left: To develop
the screws and nuts, press switch direction of rotation (4) right to the point blank range. Switch (6) the choice of operation
should be in position «Drilling». It must be done to change the direction of rotation when the spindle rotates a drill!
8.11. Not used in rotation to the left mode of attack.
8.12. When you need to vent large diameter, is recommended first to break a small opening, which will then be drilling to
the desired size. This will prevent overloading the drill. Drilling deep holes should be done gradually, as periodically removed