Rae ToxiRAE Pro User Manual Download

Page: 9 / 68

ToxiRAE Pro User’s Guide

2. Specifications

ToxiRAE Pro Specifications

Dimensions

118 mm x 60 mm x 30 mm (4.6" x 2.4" x 1.2")

Weight

220g (7.76 oz)

Sensor

Over 20 intelligent interchangeable field-replaceable electrochemical sensors

Battery

Rechargeable Li-ion battery
• Operating time > 30 hours (normal operation)
• Recharge time < 4 hours through charging cradle

Display

Graphical LCD display with white LED backlighting (activated when monitor

is in alarm or with a button press)

Display Readout

Real-time reading of concentrations in parts per million; battery status;

datalogging on/off status; wireless on/off and reception quality; STEL, TWA,
and peak values (as applicable)

Keypad

2 buttons for operation and programming

Sampling

Diffusion

Calibration

Automatic with AutoRAE 2 Test and Calibration Station or manual

Alarm Modes

Wireless remote alarm notification, audible (95dB @ 30cm), vibration, visible

alarm (flashing bright red LEDs), and on-screen indication of alarm conditions
• Additional diagnostic alarm and display message for low battery

Datalogging

• Continuous Datalogging with a three-month capacity (at one-minute

intervals)
• User-configurable datalogging interval (from 1 to 3,600 seconds)

Communication

and Data

Download

• Data download and instrument set-up on PC via charging and PC

communication cradle
• Data download via AutoRAE 2 Automated Test and Calibration Station
• Wireless data and status transmission via built-in RF modem (optional)

Wireless Network

RAE Systems Dedicated Wireless Network

Wireless

Frequency

ISM license-free bands

Wireless Range

(Typical)

300 feet (100 meters)

Operating

Temperature

-4° to 131° F (-20° to 55° C)

Humidity

0 to 95% relative humidity (non-condensing)

Dust and Water

Resistance

IP-65 rating for dust and water ingress protection (validated by an independent

test laboratory)

Hazardous

Location

Approvals

US and Canada

Class I, Div. 1; Groups A,B,C,D T4

Class I, Zone 0 A/Exia IIC T4

Europe

ATEX:

II 1G, Ex ia IIC Ga T4

IECEx: Ex ia IIC Ga T4

China

Ex ia IIC T4

CE Compliance

(European

Conformity)

EMC directive: 2004/108/EC

R&TTE directive: 1999/5/EC
ATEX directive: 94/9/EC

Warranty

• Two years on non-consumable components and CO, H

S, and O

sensors

• One year on all other sensors, battery, and consumable parts

Specifications are subject to change.

Summary of Contents for ToxiRAE Pro




































































Search results

Summary of Contents for ToxiRAE Pro

Reviews:

Related manuals for ToxiRAE Pro

Brands by name

Popular brands

Rae ToxiRAE Pro, User Manual

Search results

Summary of Contents for ToxiRAE Pro

Reviews:

Related manuals for ToxiRAE Pro

Brands by name

Popular brands