Rae ToxiRAE Pro User Manual Download

Page: 61 / 68

ToxiRAE Pro User’s Guide

19. Troubleshooting

Problem

Possible Reasons & Solutions

Cannot turn on power

Reasons:

Depleted battery.
Defective battery.

Solutions:

Replace battery.

Lost password

Solutions:

Use ProRAE Studio II

software to change the
password.

Call Technical Support

at +1 408-752-0723 or
toll-free at
+1 888-723-4800

Reading abnormally
Low

Reasons:

Calibration Adapter is
attached.
Incorrect calibration.

Solutions:

Remove Calibration

Adapter.
Calibrate the ToxiRAE
Pro.

Buzzer, LEDs, or
vibration alarm
Inoperative

Reasons:

Alarms may be turned
off.
Blocked alarm port.
Bad buzzer, LEDs, or
vibration alarm.

Solutions:

Enable alarms in the
Buzzer & Light section
of the Alarm Settings
sub-menu in the
Programming menu.
Unblock alarm port.
Call authorized service
center.

Summary of Contents for ToxiRAE Pro




































































Search results

Summary of Contents for ToxiRAE Pro

Reviews:

Related manuals for ToxiRAE Pro

Brands by name

Popular brands

Rae ToxiRAE Pro, User Manual

Search results

Summary of Contents for ToxiRAE Pro

Reviews:

Related manuals for ToxiRAE Pro

Brands by name

Popular brands