manualshive.com logo in svg

Radyne DMD2401 LB, Installation And Operation Manual, Page: 9 / 179

Share
Download
Radyne DMD2401 LB Installation And Operation Manual Download Page 9

Table of Contents

DMD2401 LB/ST L-Band Satellite Modem and ODU Driver

viii

TM075 - Rev. 1.3

3.8  ESC Backward Alarms_____________________________________________3-7

3.8.1  To Disable the ESC Backward Alarms _______________________________3-7

3.9  IDR or IBS/D&I Configuration Instructions ______________________________3-7

3.9.1  IDR Configuration (Older Modems)__________________________________3-7

3.9.2  IBS/D&I Configuration (Older Modems) ______________________________3-8

3.10  Configuring the DMD2401 for Drop and Insert _________________________3-8

3.10.1  Interface Type_________________________________________________3-9

3.10.2  Mode________________________________________________________3-9

3.10.3  Data Rate ____________________________________________________3-9

3.10.4  Terrestrial Framing - Drop Mode/Insert Mode ________________________3-10

3.10.4.1  Insert Terrestrial Frame Source _________________________________3-11

3.10.5  Alarms _____________________________________________________3-11

3.11  Drop and Insert Mapping _________________________________________3-12

3.12  Loopbacks ____________________________________________________3-13

3.12.1  Terrestrial Loopback ___________________________________________3-13

3.12.2  Baseband Loopback___________________________________________3-14

3.12.3  IF Loopback _________________________________________________3-14

Section 4 – User Interfaces

4.0  User Interfaces __________________________________________________4-1

4.1  Front Panel User Interface__________________________________________4-1

4.1.1  Front Panel LCD Display _________________________________________4-2

4.1.2  Front Panel LED Indicators________________________________________4-2

4.1.3  Front Panel Keypad _____________________________________________4-3

4.1.4  Parameter Setup _______________________________________________4-3

4.2  Front Panel Control Menu Screens ___________________________________4-4

4.2.2  Modulator _____________________________________________________4-4

4.2.4  Interface Menu Options and Parameters _____________________________4-8

4.2.5  Monitor Menu Options and Parameters ______________________________4-9

4.2.6  Alarms Menu Options and Parameters ______________________________4-10

4.2.7  System Menu Options and Parameters _____________________________4-18

4.2.8  Test Menu Options and Parameters ________________________________4-20

4.3  Terminal Mode Control ___________________________________________4-21

4.3.1  Modem Terminal Mode Control____________________________________4-21

4.3.2  Modem Setup for Terminal Mode __________________________________4-21

Summary of Contents for DMD2401 LB




















































































































































































Reviews:

No comments