manualshive.com logo in svg

Radyne DMD2401 LB, Installation And Operation Manual, Page: 8 / 179

Share
Download
Radyne DMD2401 LB Installation And Operation Manual Download Page 8

DMD2401 LB/ST L-Band Satellite Modem and ODU Driver

Table of Contents

TM075 - Rev. 1.3

vii

Table of Contents

1.0  Description______________________________________________________1-1

1.1  DMD2401 Available Options ________________________________________1-2

1.1.1  Reed-Solomon Codec ___________________________________________1-2

1.1.2  Sequential Decoding ____________________________________________1-2

1.1.3  Asynchronous Overhead Channel __________________________________1-2

1.1.4  Customized Options _____________________________________________1-3

1.1.5  8PSK Modulation _______________________________________________1-3

1.1.6  Analog AGC Voltage ____________________________________________1-3

1.1.7  Drop and Insert (D&I) ____________________________________________1-3

Section 2 – Installation

2.0  Installation Requirements __________________________________________2-1

2.1  Unpacking ______________________________________________________2-1

2.2  Removal and Assembly ____________________________________________2-2

2.3  Mounting Considerations ___________________________________________2-2

2.4  Modem Checkout_________________________________________________2-2

2.4.1  Initial Power-Up ________________________________________________2-2

Section 3 – Operation

3.0  Theory of Operation_______________________________________________3-1

3.1  DMD2401 LB/ST Operation _________________________________________3-1

3.2  Applications _____________________________________________________3-1

3.2.1  SCPC Point-to-Point Links ________________________________________3-1

3.2.2  SCPC Point to Multi–Point Links in a Broadcast Application ______________3-2

3.2.3  DAMA (Demand Assigned Multiple Access) ___________________________3-2

3.2.4  TDMA (Time Division Multiple Access) Remote Site Application ___________3-2

3.3  DMD2401 LB/ST Initial Configuration Check ____________________________3-3

3.4  DMD2401 LB/ST Automatic Uplink Power Control (AUPC Operation)_________3-3

3.5  DMD2401 LB/ST Asynchronous Overhead Operation_____________________3-4

3.5.1  Asynchronous Framing/Multiplexer Capability _________________________3-4

3.6  Standard IBS Mode _______________________________________________3-6

3.7  Asynchronous Multiplexer Mode _____________________________________3-6

Summary of Contents for DMD2401 LB




















































































































































































Reviews:

No comments