Radyne DMD2401 LB Installation And Operation Manual Download Page 162 | Manualshive

Page: 162 / 179

background image

DMD2401 LB/ST L-Band Satellite Modem and ODU Driver

Technical Specifications

TM075 - Rev. 1.3

7-3

7.6 Monitor and Control

All operating parameters can be monitored and controlled via the Front Panel display/keypad, or
the RS-485 or RS-232 Serial Control Channel in either Terminal or Command Modes. The
following Modem Parameters may be controlled and/or monitored:

Modem Mode (Closed Net, IDR, IBS, D&I)
Transmit and Receive Frequencies
Transmit and Receive Offsets
Modulator Power Level
Modulator On/Off
Modulator/Demodulator Modulation (BPSK, QPSK, OQPSK, or 8PSK)
Modulator/Demodulator Data Rates (1 Bps steps)
Modulator/Demodulator Code Rates (1/2, 3/4, 7/8, 2/3)
Modulator/Demodulator Differential Decoders (On/Off)
Modulator/Demodulator Scrambler (On/Off)
Modulator/Demodulator Data (inverted or non-inverted)
Modulator/Demodulator Clock Source and Phase
Demodulator FIFO Size, Delay and Status
Demodulator Eb/No
Demodulator Low Eb/No
Demodulator Measure BER and Estimated BER
Modulator/Demodulator Alarms
Modem Remote Port Address, Data Rate, Enable/Disable Modem Test Modes
Mod/Demod Framing (None, 96K, 1/15 (IBS), 1/15 (Async))

7.7 Options

Concatenated Codec:

A Reed-Solomon codec is available.

Asynchronous Channel:

Asynchronous overhead channel for remote control and
order-wire applications.

7.8 Environmental

Input Power:

100 - 240 VAC, 50 - 60 Hz, 6.0 A
(IEC 3-pin Power Connector with Switch)

Outdoor Unit Power:

6 A maximum combined is available from Rx and Tx
outputs.

Operating Temperature:

0 – 50°C, 95% humidity, non-condensing

Storage Temperature:

-20 to 70°C, 99% humidity, non-condensing

7.9 Physical

Chassis size:

19 x 17 x 3.5 inches
(48.26 x 43.2 x 4.45 cm)

Weight:

16 pounds (7.2 Kg)

Shipping Weight:

20 pounds (9.0 Kg)

«
...
160
161
162
163
164
...
»

Summary of Contents for DMD2401 LB




















































































































































































Reviews:

No comments

Related manuals for DMD2401 LB

Brand: SWEEX Pages: 3

WAGO-TO-PASS 761-510

Brand: WAGO Pages: 82

Brand: NCXX Pages: 12

Brand: Racelogic Pages: 6

Brand: TP-Link Pages: 24

Brand: MLis Pages: 54

Brand: Medion Pages: 2

Brand: Wireless Matrix Pages: 16

Brand: Four-Faith Pages: 34

Brand: Packet One Pages: 50

Brand: NETGEAR Pages: 2

Brand: Franklin Pages: 22

Brand: Hughes Pages: 134

Brand: Zhone Pages: 2

Brand: NetComm Pages: 112

E78-DTU(470LN22)

Brand: Ebyte Pages: 50

Brand: Ebyte Pages: 30

Ultra Performace Series

Brand: D-Link Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands