background image

1997 Radionics                                      All rights reserved

The Radionics logo is a registered trademark of Radionics,

    1800 Abbott Street, Salinas, CA  93901, USA

74-07661-000-B      01/97
D9024/D10024 Operation

    

Page 8 of 13

D10024

SHIFT

G

T

6

[Active]  1)Commission 2)Test   3)Time  [1]
4)Enable 5)Disable     6)PRINT  7)View

O

A

N

0

B

C

P

1

2

D

Q

E

R

3

4

F

S

5

H

U

7

V

I

J

W

8

9

K

X

L

Y

M

Z

CHANGE

Figure 3: Operator’s Menu, Main Level

D.4.a.  System Tests

Select the second option, 

2) Test

,  key from the Main Level Menu to open the Test Menu.  This

allows the operator to test:

• 

the LEDs on the Front Panel Display

• 

the devices connected to the system.

If no action is taken, the display reverts to the normal display after one minute.
The third option on this menu, 

3) Outputs

, is not available to Level Two.

D10024

SHIFT

G
T

6

 1) LEDs   2) Walk Test zone  3) Outputs

O

A
N

0

B

C
P

1

2

D
Q

E
R

3

4

F
S

5

H
U

7

V

I

J

W

8

9

K
X

L
Y

M
Z

CHANGE

Figure 4:  Test Menu

D.4.a.1.  LEDs Test

Select the first option,

 1) LEDs

, by pressing the

 1

 key.  The panel will flash all LEDs on the

LED Display and step through all the 

Alarm

 and 

Trouble

 LEDs in the ZONE/AREA Display.

On completion of the test, the Display will report the results of the test and automatically

revert to the normal menu after one minute.
To interrupt and end the test, press the NO key.

D.4.a.2.  Walk Test

The Walk Test allows the operator to test the system devices without having to reset the

panel after each device is tested.  Select the second option, 

2) Walk Test zone

, by pressing

the 

2

 key.

Note: If no action is taken within one minute, the display reverts to the normal display.  Press the >

key to restore the test display.

The display prompts, “Ring bells?”
Press the 

YES 

key to activate notification appliances briefly as each device is tested, or

press the 

NO

 key to bypass the indicator test.

The display prompts, “Test from zone? (Please key in number, then press Enter).”
Enter the number of the first zone to be tested.

Summary of Contents for D9024














Reviews: