background image

1997 Radionics                                      All rights reserved

The Radionics logo is a registered trademark of Radionics,

    1800 Abbott Street, Salinas, CA  93901, USA

74-07661-000-B      01/97
D9024/D10024 Operation

    

Page 7 of 13

D10024

SHIFT

Alarm

Silence

LED DISPLAY

ZONE/AREA DISPLAY

">" KEY

ALPHANUMERIC DISPLAY

SYSTEM RESET

KEY

TROUBLE SILENCE

KEY

SYSTEM TROUBLE

LED

TROUBLE SILENCED

LED

ALARM

LED

ALARM SILENCED

LED

AC POWER

LED

ALARM SILENCE

KEY

FIRE DRILL

KEY

System
Trouble

1

3

Alarm

5

4

6

Trouble
Silenced

Point

Bypassed

7

8

9

Earth
Fault

A
N

0

B
O

C
P

1

2

System

Reset

Trouble
Silence

E
R

4

D
Q

3

F
S

5

10

11

12

Fault

Sounder

13

14

15

Alarm

Silenced

16

17

CPU
Reset

19

20

AC Power

Fire
Drill

6

7

I

V

J

W

8

9

Letters

Numbers

ENTER

NO

Keyword

YES

K
X

L
Y

M

Z

CHANGE

Figure 2: Level Two Controls

D.3.b.  Alarm Signal Response

Press the 

Alarm Silence

 key to turn off notification appliances external to the panel.  The

 Alarm

Silenced

 LED will light.  Pressing the 

Alarm Silence

 key again turns on the external notification

appliances.  Press the 

Trouble silence

 key to turn off the panel buzzer.  The amber 

Trouble

Silenced

 LED will light.  Press the

 System Reset

 key to reset the system.  The 

Alarm

 and

Silenced

 LEDs will go out and the Alphanumeric Display will return to normal.

Note: The panel will not allow a reset from an Alarm condition until the notification appliances have

been silenced.

To return the system to Level Two, press the “>“ key, and select 

5) Disable

 from the

Alphanumeric Display.  Select 

3)Keys

 from the display.  The display will return to normal.  Press

the 

Fire Drill

 key to verify that the keys are disabled.  The display will prompt, “do you want to

enable the Control Keys?”  Press the 

NO

 key.  The display will return to normal.

D.4.  Operator’s Menu

Pressing the “>“ key will open the Operator’s Menu, Main Level, on the Alphanumeric Display.  The

first option, 

1 Commission

, is not available to Level Two Operators.  See the Programmer’s Guide

for commissioning and programming information.  The other options on the Main Level permit tests

and enabling/disabling of various system functions.

Summary of Contents for D9024














Reviews: